Product introduction Double deck cross worktable moving structure, many kinds of probe modes is combined such as touch-probe system and optical image system. CCD imaging technology and advanced image-processing technology are combined too. This machi
Product introduction Full-closed moving-bridge structure, with high precision, speed, and stable capability. Many probe head systems can be chosen to match: optical CCD image probe head, laser probe head. It satisfies precision dimension checking of
Electronics Forum | Fri Sep 24 16:01:07 EDT 2010 | dougt
I remember this problem but can't remember exactly what the reason was. It might have been the wrong pullup resistor on the MEI interface board used for the home photo on the y axis. You are right, after a couple hours the machine would work fine.
Electronics Forum | Thu Nov 03 01:39:53 EDT 2022 | spacecase
Thank you for the response, left the machine turned off for a good period of time and somehow the issue solved itself. I was able to calibrate the next day and homing hasn't been an issue. However now I'm having another problem where it gets 4 comple
Used SMT Equipment | In-Circuit Testers
Agilent E4411B ESA-L Spectrum Analyzer ESA-L Spectrum Analyzer, 1 MHz to 1.5 GHz (75-ohm) The Agilent Technologies E4411B spectrum analyzer is a wide band, very sensitive receiver. It works on the principle of "super-heterodyne receiver" to c
Used SMT Equipment | Pick and Place/Feeders
Make: YAMAHAModel: YG200Details:1.High-Speed Performance: Mounting speed up to 60000 CPH (0.06 seconds per chip) .2.High Precision: Ensures a mounting accuracy of up to ±50 microns, with a repeat accuracy of up to ±30 microns .3.Wide Range of Compone
Industry News | 2020-10-24 02:04:11.0
On November 3rd to 5th, 2020,Unicomp Technology will bring the latest technology and products to the ELECTRONIC SOUTH CHINA 2020,Welcome to visit the Unicomp Technology booth at 9D30,Hall 9. Shenzhen International Convention and Exhibition Center!
Industry News | 2021-05-21 03:56:59.0
LED lamp bead because of energy saving, low carbon environmental protection, no strobe, no radiation, high brightness, low heat advantages are gradually replacing the fluorescent lamp on the market, its application scope is expanding,although LED has many advantages, if the production or operation is not appropriate,there will be LED strip use fault phenomenon. LED lamp strip manufacturers also begin to pay more and more attention to the problem of production quality, then what equipment can be used for LED lamp strip backlight detection? Unicomp Technology here recommended AX8200L LED strip backlight detection equipment.
Parts & Supplies | Pick and Place/Feeders
GIC-F01 FUJI NXT Feeder Calibration JIG It is essential for this equipment that enhanced productivity , installation and quality improvement As the high efficiency vision camera is asked in order to investigate precisely and repair the error of
Parts & Supplies | Pick and Place/Feeders
GIC-K01 KME CM402 Feeder Calibration JIG GIC-K01 KME CM402 Feeder Calibration JIG It is essential for this equipment that enhanced productivity , installation and quality improvement As the high efficiency vision camera is asked in order to inves
Technical Library | 2024-04-29 21:39:52.0
In this paper, we develop and put into practice an Automatic Optical Inspection (AOI) system based on machine vision to check the holes on a printed circuit board (PCB). We incorporate the hardware and software. For the hardware part, we combine a PC, the three-axis positioning system, a lighting device and CCD cameras. For the software part, we utilize image registration, image segmentation, drill numbering, drill contrast, and defect displays to achieve this system. Results indicated that an accuracy of 5µm could be achieved in errors of the PCB holes allowing comparisons to be made. This is significant in inspecting the missing, the multi-hole and the incorrect location of the holes. However, previous work only focusses on one or other feature of the holes. Our research is able to assess multiple features: missing holes, incorrectly located holes and excessive holes. Equally, our results could be displayed as a bar chart and target plot. This has not been achieved before. These displays help users analyze the causes of errors and immediately correct the problems. Additionally, this AOI system is valuable for checking a large number of holes and finding out the defective ones on a PCB. Meanwhile, we apply a 0.1mm image resolution which is better than others used in industry. We set a detecting standard based on 2mm diameter of circles to diagnose the quality of the holes within 10 seconds.
03009202S01 SLIDER / HANDLE X-SERIES 03009210-04 TRAILING CABLE ANALOGOUS 1P 03009259S02 CUTTER UNIT (SIPLACE HF) 03009269S02 DC-Gear motor with synchronizing disc 03009270-01 DC-Motor 2657 W 048CR 32/1 7:1 03009343S01 LABEL NUMBER 204 03009391
350x400mm Dual Table High-speed Four-axis Visual PCB Router Milling Cutter PCB Router Machine Features: This system has two-slide tables for high volume production. And it has lower stress to protect PCBA to ensure smooth cutting edge. Imported m
Career Center | Wesley Chapel, Florida USA | Engineering,Management,Quality Control
15 years of experience on Electronic Manufacturing. Certified SMT Process Engineer TQM Knowledge Statistics DOE Screen Printer Thermal Process Knowledge JIT International Project Engineering Experience
Career Center | cabuyao, Philippines | Engineering
I had 9 years working as a technician starting in Smart electronic)as Mainline Technician. SGIC(Sanritsu Great International Corporation) as SMT mainline Techinician and IMI (Integrated Micro-Electronics INC,)as SMT Process Technician.
KingFei SMT Tech | https://www.smtspare-parts.com/sale-35537277-hpx-nt4-015-sensor-with-fiber-9498-396-00701-for-assembleon-ax-machine.html
: Assembleon AX Machine 9498 396 00259Trolley lift controller 9498 396 00442Footswitch 9498 396 00521Z-SPINDLE 9498 396 00562Nozzlepunches L2-5 (4pc
Qinyi Electronics Co.,Ltd | https://www.qy-smt.com/shop/page/52?order=name+desc
Public Pricelist Public Pricelist Z-Hight Motor J9080327B ¥ 0.00 0.0 CNY Z-Belt 3 Base ¥ 0.00 0.0 CNY Z-BELT 5 Base(AX) ¥ 0.00 0.0 CNY Z-Axis cpl. DLM2 ¥ 0.00 0.0 CNY Z-Axis cpl. DLM2 ¥ 0.00 0.0 CNY Z-Axis Servo ASM HC-13H00336L-S14
winsouce.jpg)
.gif)
