Industry Directory | Consultant / Service Provider / Equipment Dealer / Broker / Auctions / Manufacturer's Representative / Training Provider
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
AUTOTRONIK-SMT is a German company provides High Precision SMT Pick & Place Machine, Stencil Printer,Reflow Oven. which are low-cost, high accuracy ,with Laser & Vision alignment, can handle 0201,0402,SOIC,PLCC,Micro-BGA,0.3mm QFP,..etc.
New Equipment | Rework & Repair Equipment
Finally! A High End BGA Rework System at an affordable price. Fits board up to 25" Places components from 4mm to 50mm Standard resolution Split Vision Assist for Component Alignment Plug and Play. Fully self contained with is own internal air
1.jpg)
New Equipment | Rework & Repair Equipment
The model SV560 is has a high resolution optical system for placement of components as small as 1mm. With it's rapid heat infrared area heater it can rework boards as large a 36" and 36 layers. High Resolution HDMI Vision System Fits Boards up t
Electronics Forum | Thu Sep 12 10:45:29 EDT 2002 | pbarton
We have used a laser cut stencil 0.15mm (0.006") thick with 0.3mm (0.012") square apertures radiused in the corners 0.06mm (0.0025") to aid paste release. This approach with the (type 3) paste we use has proven successful on thousands of devices plac
Electronics Forum | Thu Sep 05 03:23:14 EDT 2002 | manic
Hi, I encountered a problem with pbga. One edge either warp downwards or upwards creating bridging or open. This pbga have fr4 at the bottom (compound molding at the top). The fr4 is bigger than the top compound by 3mm at each edge. Pls help. Than
Used SMT Equipment | Chipshooters / Chip Mounters
FUJI, Chip Shooter, type CP643E, s.n. 2066, Left to right, cap. 40.000 CPH, Device input 140-8mm, with 20 heades, 6 nozels each, 2 tables 70 feeders each, PCB dimensions Max: 457mm x 356mm Min: 80mm x 60mm,Board Thickness: 0.3 to 4.0 mm, Component ca
Used SMT Equipment | Chipshooters / Chip Mounters
FUJI, Chip Shooter, type CP643E, s.n. 1278, Left to right, cap. 40.000 CPH, Device input 140-8mm, with 20 heades, 6 nozels each, 2 tables 70 feeders each, PCB dimensions Max: 457mm x 356mm Min: 80mm x 60mm,Board Thickness: 0.3 to 4.0 mm, Component ca
Industry News | 2003-07-02 08:54:26.0
A novel unreinforced, thermally conductive, pressure sensitive adhesive tape delivers very high bond strength to low-energy surfaces.
Industry News | 2008-08-11 23:45:48.0
OXFORD, CT � August 2008 � MIRTEC Corp., the AOI market leader in North America, announces that it will display the MV-7L In-Line AOI System in booth 424 at the upcoming SMTA International exhibition and conference, scheduled to take place August 19-20, 2008 in Orlando. FL.
Parts & Supplies | Repair/Rework
The RocHard 1 MilProbe is a 0.3" long Micro-tip in a 4 3/8" long hex shape stainless steel handle. The Micro-tip is tapered to a one mil diameter tip for TAB, BGA, and other ultra fine pitch rework. The tip is either straight (SH-341) or 50? angled a
Parts & Supplies | Screen Printers
Product Name: 10inch; MPM printing doctor blades Part Number: 10 inch; 254mm length Description: 10 inch; MPM printers 254mm * 32mm * 0.3mm scraper blades Applicable models: UP2000 machine 10 inch; MPM printers 254mm * 32mm * 0.3mm scraper blad
Technical Library | 2023-07-25 16:50:02.0
Some of the new handheld communication devices offer real challenges to the paste printing process. Normally, there are very small devices like 01005 chip components as well as 0.3 mm pitch uBGA along with other devices that require higher deposits of solder paste. Surface mount connectors or RF shields with coplanarity issues fall into this category. Aperture sizes for the small devices require a stencil thickness in the 50 to 75 um (2-3 mils) range for effective paste transfer whereas the RF shield and SMT connector would like at least 150 um (6 mils) paste height. Spacing is too small to use normal step stencils. This paper will explore a different type of step stencil for this application; a "Two-Print Stencil Process" step stencil. Here is a brief description of a "Two-Print Stencil Process". A 50 to 75 um (2-3 mils) stencil is used to print solder paste for the 01005, 0.3 mm pitch uBGA and other fine pitch components. While this paste is still wet a second in-line stencil printer is used to print all other components using a second thicker stencil. This second stencil has relief pockets on the contact side of the stencil any paste was printed with the first stencil. Design guidelines for minimum keep-out distances between the relief step, the fine pitch apertures, and the RF Shields apertures as well relief pocket height clearance of the paste printed by the first print stencil will be provided.
Technical Library | 2017-09-28 16:36:33.0
These nano-coatings also refine the solder paste brick shape giving improved print definition. These two benefits combine to help the solder paste printing process produce an adequate amount of solder paste in the correct position on the circuit board pads. Today, stencil aperture area ratios from 0.66 down to 0.40 are commonly used and make paste printing a challenge. This paper presents data on small area ratio printing for component designs including 01005 Imperial (0402 metric) and smaller 03015 metric and 0201 metric chip components and 0.3 mm and 0.4 mm pitch micro BGAs.
Live Demo of the SRT Sierra 1000 BGA Rework Station. Tune in, watch, learn and ask questions about BGA Rework Stations, BGA Rework Services, BGA Reballing and more! http://www.pcb-repair.com/bga-rework-station/
Dennis Odonnell , Vice President of Precision PCB Services, Inc., Oroville CA Explains How to Evaluate a BGA Rework Station ! #BGA Rework Stations http://www.pcb-repair.com/bga-rework-station/
Events Calendar | Mon Apr 23 00:00:00 EDT 2018 - Thu Apr 26 00:00:00 EDT 2018 | Shanghai, China
SMTA China East Conference 2018
Events Calendar | Thu Mar 18 00:00:00 EDT 2021 - Thu Mar 18 00:00:00 EDT 2021 | ,
India Chapter Webinar: PCBA Process Qualifications
Career Center | , Israel | Engineering,Maintenance,Technical Support
I was born on June , 1972 in Khmelnitsky city , Ukraine . I am male. From 1979 to 1987 I was studying at secondary school #7, having finished which I entered the Technical College of Khmelnitsky in specialty Machine Tools with Computer Numeric Contr
Career Center | , | Engineering,Production
Project Management, SMT Process Engineering
Qinyi Electronics Co.,Ltd | https://www.qy-smt.com/shop/aa1at00-nxt-head-v12-h12-h08-0-3-mm-nozzle-181473?page=113&category=1115&order=list_price+asc
FUJI NXT HEAD V12/H12/H08 0.3 MM nozzle AA1AT00 | QYSMT × Home about Us ABOUT US FAQ SMT spare parts SMT surplus equipment SMT peripheral equipments News Contact US 0 0 Sign in contact us Products FUJI NXT HEAD V12/H12/H08
| https://pcbasupplies.com/jm-20-sn60-pb40-0-3-mm/
JM-20 Sn60/Pb40 - 0.3 mm No Clean Leaded Flux Cored Solder Wire - PCBASupplies Login Create Account Contact View My Cart Menu
