Desktop Pick And Place Machine SMT Prototyping pick place. High-Speed High-Performance LED Mounting Machine chip mounter Product Introduction: SZTech SMT Series Desktop Pick And Place Machine main features: Small volume, easy to operate, run stable,
New Equipment | Rework & Repair Equipment
The Hakko FR-1418 BGA Rework System is constructed of heavy-walled aluminum castings for unsurpassed precision and stability and uses precisely controlled solder reflow profiles. The system features a unique gantry style construction similar to that
Electronics Forum | Thu Sep 05 03:23:14 EDT 2002 | manic
Hi, I encountered a problem with pbga. One edge either warp downwards or upwards creating bridging or open. This pbga have fr4 at the bottom (compound molding at the top). The fr4 is bigger than the top compound by 3mm at each edge. Pls help. Than
Electronics Forum | Tue Sep 10 08:22:36 EDT 2002 | davef
I doubt that the interposer is FR4, it's more likely to be BT. Warp during reflow is a function of material a reflow recipe. Your ramp is too fast and is causing the interposer to bend like a potato chip.
Industry News | 2001-02-26 11:18:45.0
Innovative Flextac Stencils simplify BGA rework. These self-sticking laser cut, polymer solder paste stencils use a residue-free adhesive similar to Post-it Notes to seal around BGA pads to ensure that solder paste will not bleed under the stencil when the paste is applied. Disposable Flextac Stencils are easy to use and will not leave any residue on the board surface.
Industry News | 2016-10-26 14:55:50.0
Vass, NC – Sept 20, 2016 – PACE Worldwide announces an introductory promotion in conjunction with the launch of their new TF 1800 BGA/SMD Rework System, which began shipping in October. For a limited time, PACE will provide 10 Heat Focusing Nozzles free of charge with the purchase of each TF 1800 System, a value of over $3,400 (£2,700/€3,340).
Technical Library | 2017-08-17 12:23:27.0
A novel epoxy flux EF-A was developed with good compatibility with no-clean solder pastes, and imparts high reliability for BGA assembly at a low cost. This compatibility with solder pastes is achieved by a well-engineered miscibility between epoxy and no-clean solder paste flux systems, and is further assured with the introduction of a venting channel. The compatibility enables a single bonding step for BGAs or CSPs, which exhibit high thermal warpage, to form a high-reliability assembly. Requirements in drop test, thermal cycling test (TCT), and SIR are all met by this epoxy flux, EF-A. The high viscosity stability at ambient temperature is another critical element in building a robust and userfriendly epoxy flux system. EF-A can be deposited with dipping, dispensing, and jetting. Its 75°C Tg facilitates good reworkability and minimizes the adverse impact of unfilled underfill material on TCT of BGA assemblies.
Enter PACE’s TF Series BGA/SMD Rework Systems. With its groundbreaking, patented Inductive-Convection Heating Technology, the TF Series top-side heater reaches the target temperature in just seconds for safe, rapid solder joint reflow in virtually an
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/dage/about/blog/heated-stage
) and BGA ball and solder paste alloy differences. During reflow, board/component warpage, poor wetting and co-planarity issues can also create this
Imagineering, Inc. | https://www.pcbnet.com/capabilities/assembly/technology-roadmap/
. Layer Count 50 Max. Working Panel Size 21" x 31" Max. Board Thickness .300" Min. Board Thickness 0.16"(6L) Min. Line/Space • I/L - 2 / 1.5mil (HDI) • O/L - 2 / 1.5 mil (HDI) Warpage .001" / sq. in. BGA Pitch 0.20mm Layer to Layer Registration 3 mil
