New Equipment | Cleaning Agents
CYBERSOLV® C8508 is the latest generation spray cleaner for reflow ovens and general equipment maintenance cleaning. CYBERSOLV® C8508 has been tested on the toughest baked on flux residues with great success and has proven effective on the latest lea
Electronics Forum | Sun Aug 02 23:12:25 EDT 2015 | galler
For anyone having problems in burning boot loader in an Atmega328, the burnt atmega328 should be the most common tricky problem. some makers users are looking for an alternative to replace it. Now some say that Atmega328P-PU could be a great alternat
Electronics Forum | Wed Aug 05 09:16:16 EDT 2015 | emeto
If the package of both parts is the same and the Pin layout is the same you can replace it.
Industry News | 2017-10-05 05:56:21.0
The SMTA Capital Chapter is pleased to announce its third meeting of 2017 on November 7th, scheduled from 5:30 pm to 8:00 pm at ZESTRON Americas, 11285 Assett Loop, Manassas, VA, 20109. Ravi Parthasarathy, Senior Application Engineer, ZESTRON Americas, will present “Cleaning Before Conformal Coating” and “pH Neutral Cleaning Agents - Market Expectation and Field Performance”.
Industry News | 2018-10-25 15:13:49.0
Industry-leading associations IPC and SMTA jointly announce the High-Reliability Cleaning and Conformal Coating Conference, scheduled to take place November 13-15, 2018 at Chicago Marriott, Schaumburg, Illinois. The conference is focused on the cleanliness of highly dense electronic assemblies to achieve quality and reliability within the stated in-field environment.
Technical Library | 2017-08-17 12:28:30.0
At SMT assembly, flux outgassing/drying is difficult for devices with poor venting channel, and resulted in insufficiently dried/burnt-off flux residue for no-clean process. Examples including: Large low stand-off components such as QFN, LGA Components covered under electromagnetic shield which has either no or few venting holes Components assembled within cavity of board Any other devices with small open space around solder joints
Technical Library | 2020-11-24 23:01:04.0
The miniaturization trend is driving industry to adopting low standoff components or components in cavity. The cost reduction pressure is pushing telecommunication industry to combine assembly of components and electromagnetic shield in one single reflow process. As a result, the flux outgassing/drying is getting very difficult for devices due to poor venting channel. This resulted in insufficiently dried/burnt-off flux residue. For a properly formulated flux, the remaining flux activity posed no issue in a dried flux residue for no-clean process. However, when venting channel is blocked, not only solvents remain, but also activators could not be burnt off. The presence of solvents allows mobility of active ingredients and the associated corrosion, thus poses a major threat to the reliability. In this work, a new halogen-free no-clean SnAgCu solder paste, 33-76-1, has been developed. This solder paste exhibited SIR value above the IPC spec 100 MΩ without any dendrite formation, even with a wet flux residue on the comb pattern. The wet flux residue was caused by covering the comb pattern with 10 mm × 10 mm glass slide during reflow and SIR testing in order to mimic the poorly vented low standoff components. The paste 33-76-1 also showed very good SMT assembly performance, including voiding of QFN and HIP resistance. The wetting ability of paste 33-76-1 was very good under nitrogen. For air reflow, 33-76-1 still matched paste C which is widely accepted by industry for air reflow process. The above good performance on both non-corrosivity with wet flux residue and robust SMT process can only be accomplished through a breakthrough in flux technology.
Flux spray coating on a PCB with uniformal thickness down to 5 microns, with clear edge definition and minimal overspray. Can coat large or shoot dots with the same jet.
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/07/flux.pdf
), decreasing cooling and condensation efficiencies. The time period for this may vary depending on the type of solder paste flux used, the weekly consumption rate of paste, and oven temperature profiles
| https://pcbasupplies.com/wave-soldering-flux-selective/
Wave Soldering Flux, Selective Soldering Flux - PCBASupplies Login Create Account Contact View My Cart Menu × Categories Hand Soldering
COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.
2481 Hilton Drive
Gainesville, GA USA
Phone: (770) 538-0411
