New Equipment | Solder Materials
SM-150G and SM-155P are single component epoxy adhesive, specifically designed for the bonding of surface mount devices to PCB in the lead-free process. SM-150G is suitable for glue dot process and SM-155P is suitable for the printing machine process
Epoxy 4089 is a single part, epoxy adhesive used for bonding SMT components to a PWB prior to double sided reflow or wave solder assembly. Epoxy 4089 has been formulated for use in all types of high speed dispensing equipment including air pressure,
Electronics Forum | Fri Mar 30 18:24:12 EST 2001 | davef
There is no test. Beyond the issues that you mentioned that affect shear, an article published in a recent [1/01] "Journal Of Surface Mount Technology" documents that shear is also dependent on the rate of shear. You may be able to contact the auth
Electronics Forum | Sat Mar 31 08:47:24 EST 2001 | davef
Sure, researchers measure shear as an element of their material characterization process, but that does not make it an acceptance test. [Truly, this conversation is not uncommon on SMTnet. So, it would not surprise me if an enterprising something o
Used SMT Equipment | Circuit Board Assembly Products
The product introduction The SM-2009 scissors & pneumatic type separator, we use the most advanced non-stress idea to designed it, it’s help to prevent the chap phenomena as the PCB separated by the general separator, it’s improve the PCB’s quality
Industry News | 2017-08-02 07:12:18.0
As market leader in bond testing, XYZTEC is pushing the technology forward. In this month's newsletter we highlight the recent advances in thin, 3D and MEMS die bond testing. As developments in thin die change the shape of our customers' products, three fundamental difficulties for the bond test have to be overcome:
Industry News | 2014-12-11 17:22:23.0
Nordson DAGE, a division of Nordson Corporation (NASDAQ: NDSN), continues to meet the challenges for micro materials testing with the introduction of a new test method for the evaluation of die strength by means of cantilever bending where 3 point bending is not suitable for die with a thickness of less than 50 microns.
Technical Library | 2023-01-17 17:27:13.0
Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The degree of wetting, the microstructure (in particular the intermetallic layer), and the inherent strength of the solder all factor into the reliability of the solder joint. This paper presents experimental results on the effect of reflow profile on both 63%Sn 37%Pb (SnPb) and 96.5%Sn 3.0%Ag 0.5%Cu (SAC 305) solder joint shear force. Specifically, the effect of the reflow peak temperature and time above solder liquidus temperature are studied. Nine reflow profiles for SAC 305 and nine reflow profiles for SnPb have been developed with three levels of peak temperature (230 o C, 240 o C, and 250 o C for SAC 305; and 195 o C, 205 o C, and 215 o C for SnPb) and three levels of time above solder liquidus temperature (30 sec., 60 sec., and 90 sec.). The shear force data of four different sizes of chip resistors (1206, 0805, 0603, and 0402) are compared across the different profiles. The shear force of the resistors is measured at time 0 (right after assembly). The fracture surfaces have been studied using a scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS)
Technical Library | 2007-03-08 19:31:10.0
Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The degree of wetting, the microstructure (in particular the intermetallic layer), and the inherent strength of the solder all factor into the reliability of the solder joint. This paper presents experimental results on the effect of reflow profile on both 63%Sn 37%Pb (SnPb) and 96.5%Sn 3.0%Ag 0.5%Cu (SAC 305) solder joint shear force.
link:https://www.ascen.ltd/Blog/Solutio/493.html ASCEN PCB separator ASC-620 PCB cutting machine can use for cutting LED long board and also can use to the PCBA with the high component separate operation.It is the best way to replace the way to purch
SMTnet Express July 11, 2013, Subscribers: 26149, Members: Companies: 13418, Users: 34911 Effect of BGA Reballing and its Influence on Ball Shear Strength by S. Manian Ramkumar Ph.D., Andrew J. Daya, Daniel B. Lewanda; Rochester Institute
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/07/pan_APEX06.pdf
; and 195oC, 205oC, and 215oC for SnPb) and three levels of time above solder liquidus temperature (30 sec., 60 sec., and 90 sec.). The shear force data of four different sizes of chip resistors
