Industry Directory | Manufacturer
EBSO develops and manufactures cutting and bending machines for Thru Hole components and is a competent solution partner around Selective Soldering.
Leading Contract Manufacturer For Semicon And Electronics in The Philippines
The CF-9 Radial Lead Former forms and cuts 2- and 3-leaded taped radial components such as TO-92s, capacitors, transistors, LEDs, etc. - precisely and repeatedly, in standard and special forms. This machine is capable of forming and cutting up to 25
Eliminate Body Stress with Versatile CF-8 GPD's CF-8 eliminates component body stress. Versatility is the key word for the CF-8. Simple tooling changes make short or long run production jobs quick and easy. Capabilities Meets exacting military s
Electronics Forum | Tue Feb 26 08:52:35 EST 2013 | stephendo
Do you also measure job run time? IF you don't I"m sure if the change over time is measured but not the run time then the run time will go up almost as much as the change over time goes down.
Electronics Forum | Wed Feb 20 13:24:56 EST 2013 | dyoungquist
If you stop when the first completed PCB of the next run goes in the oven, wouldn't you be including the loading time for that PCB in your change over time? Wouldn't change over time be from the time your p-n-p machine stops loading the last board o
Used SMT Equipment | SMD Placement Machines
There are following Siemens machine available, 1). 1unit Siemens Siplace 80 F4 Vintage 1997 with one change over table and one WPC 2). 1Unit siemens Siplace 80 F4 Vintage 1999 with one change over ta
Used SMT Equipment | General Purpose Test & Measurement
The Tektronix R7613 oscilloscope is a graph-displaying device it draws a graph of an electrical signal. In most applications, the graph shows how signals change over time: the vertical Y axis represents voltage and the horizontal X axis represents ti
Industry News | 2016-09-14 20:57:09.0
GPD Global will exhibit and have live demonstrations of the Continuously Volumetric Pump in Booth# 424 at the upcoming SMTA International 2016 Conference and Exhibition.
Industry News | 2016-09-29 21:52:08.0
GPD Global continues to establish its presence by exhibiting at trade shows in the nation and globally with our affiliates. The most recent trade shows were SMTA International 2016 in Rosemont, IL and Semicon Taiwan. We strengthened our brand globally with these successful events.
Parts & Supplies | Pick and Place/Feeders
GFC-Y01 YAMAHA Feeder Storage Cart The feeder storage cart gives your operators a secure place to put unused feeders between set-ups minimizing failures due to improper storage or handling. When its time to change over to the next job, the cart is
Parts & Supplies | Pick and Place/Feeders
GFC-P01 PANASERT MSR Feeder Storage Cart The feeder storage cart gives your operators a secure place to put unused feeders between set-ups minimizing failures due to improper storage or handling. When its time to change over to the next job, the
Technical Library | 2014-01-30 18:08:04.0
As of today, the electronic industry is aware of the requirements for their products to be lead free. All components are typically available in lead free quality. This comprises packages like BGAs with BGA solder balls to PCB board finishes like HASL. The suppliers are providing everything that is needed. It is harder to get the old tin leaded (SnPb) components for new applications today, than lead free ones. So why has not everybody changed over fully yet and how can the challenges be overcome? A big concern in this transition process is reflow soldering. The process temperatures for lead free applications became much higher. Related with this is more stress for all the components. It affects the quality and reliability of the electronic units and products...
Technical Library | 2015-06-18 12:42:57.0
In the recent past, the Light Emitting Diode (LED) was hailed as the new energy efficient light source that would never have to be replaced. There were claims of 50,000+ hrs lifetime for the humble LED. That story has changed over the last few years as the number and diversity of the LED based products has increased. This is not to say that the original evidence was incorrect, but the initial enthusiastic estimates from the labs did not match the ultimate test, customers. As a result of poor quality products affecting the overall opinion of LED based products, it is critical that manufacturers can be confident in the quality of their product. In current times we want to have products certified, checked and ensure that we have the best quality. For the purposes of this paper we will look at one aspect of LED product, and this is the Lumen maintenance and estimated lifetime. The method described here does not seek to replace using high quality rating labs, but hopefully will allow the manufacturer to know with confidence that their prototype product, upon going to certification labs will be of a high enough quality that no expensive re-designs are required.
The CF-9 Radial Lead Former forms and cuts 2- and 3-leaded taped radial components such as TO-92s, capacitors, transistors, LEDs, etc. - precisely and repeatedly, in standard and special forms. This machine is capable of forming and cutting up to 25
Eliminate Body Stress with Versatile CF-8 GPD's CF-8 eliminates component body stress. Versatility is the key word for the CF-8. Simple tooling changes make short or long run production jobs quick and easy. Capabilities Meets exacting military s
Career Center | Fremont, California USA | Production,Quality Control
Local industry leading EMS Company seeking SMT operators. Will be doing SMT line Change overs, SMT machine operation for solder printing, placement, reflow. Solder paste height measurement and record. Solder printing quality check after solder paste
Career Center | Newbury Park, California USA | Engineering,Maintenance,Production,Quality Control
MUST BE: Proficient with Stencil Print Operations. Familiarity with SMT component types and packages. Ability to read and understand procedure document and work instructions. Operate fully automated SMT, Surface Mount Lines including: Screen Pr
Career Center | chennai, India | Engineering,Maintenance
Nokia India Pvt LTD. Sriperumpudur – Board Assembler Maintenance Technician from Sep 2009 to till now. Machines Handled Pick & Place : FUJI NXT Machines FUJI NXT - M3 II ,M3S. Reflow oven: Hot flow 3/20, 2/14. Stencil Pr
Career Center | ZAGHOUAN, Tunisia | Engineering
-Giving support to the SMT lines, pick and place machines, AOI, printers paste, reflow ovens, paste inspection, conformal coating dispenser. -Provide solutions on failures and equipment maintenance, as well as program updates and documentation. -Sett
Why Sacrifice Throughput For Change-over Time? SMTnet Express March 1, 2012, Subscribers: 24963, Members: Companies: 8801, Users: 32746 Why Sacrifice Throughput For Change-over Time? Getting the most out of your equipment in small batch
KD Electronics Ltd. | http://www.kundasmt.com/?list_32/6017.html
’ LED membrane control panelPneumatic clamps provided for magazine alignmentPneumatic pusher’s pressure regulatedHigh throughput with short magazine change-over timeSMEMA compatible Features Sturdy and stable design User friendly ‘soft touch
FKN Systek | http://fknsystek.com/KMultiblade.htm
K4000 Motorized Circular Both the K5000 and K6000 multiple blade depaneling systems use quick change blade cartridges to make the change-over from one type of panel to another quick and easy
.gif)
