Industry Directory | Distributor / Manufacturer / Manufacturer's Representative / Other
ISO 9001: 2000 Franchised Distr. of Capacitors, Resistors, Semiconductors, SMD, Connectors, Crystals, Diodes, Fuses, ICs, Lamps, LEDs, Potentiometers, Relays, Switches, Transistors, Specializes in Hard to find/Obsolete Parts
Industry Directory | Manufacturer
Manufacturer of Passive Hybrid Microelectric Components. Resistors, Capacitors, Inductors, Resistor
Electronics Forum | Fri Jul 12 22:15:56 EDT 2013 | ericrr
Sorry to build up your hopes. The latest thing to hit the air ways at work, I was accessed of fiddling with the oven settings, because there were reports of "cracked joints" there was no mention of where the cracks were, cracked at the pcb or cracke
Electronics Forum | Fri Apr 11 11:26:09 EDT 2003 | Brian W.
Cracked capacitors usually are not found at ICT. Unless the cap is completely cracked, the capacitance may not change much, and the usual failure mode is a leakage current. This is usually only seen in ESS type testing, when temperature and humidit
Used SMT Equipment | SMT Equipment
Product Name:Panasoinc high speed chip mounter NPM Product number: NPM1 Detailed product introduction NPM multifunction machine, SMT machine, machine with function function function, check the dispensing machine, is a multifunctional equipment
Used SMT Equipment | SMT Equipment
Product Name:Panasoinc high speed chip mounter NPM Product number: NPM1 Detailed product introduction NPM multifunction machine, SMT machine, machine with function function function, check the dispensing machine, is a multifunctional equipment
Industry News | 2015-06-11 16:02:18.0
MIRTEC, "The Global Leader in Inspection Technology," will exhibit its most recent solutions for System in Package (SiP) inspection and measurement at SEMICON WEST 2015; July 14-16, 2015, at the Moscone Center in San Francisco, CA. Visitors are invited to booth # 2343 for a detailed demonstration of this exciting new technology.
Industry News | 2017-04-24 19:04:48.0
This year, MIRTEC will launch several new inspection machines equipped new cutting-edge technologies. MIRTEC is proud to be promoting these new machines in booth #1J10 at NEPCON China 2017, one of the biggest technical exhibitions of SMT and EMA, from April 25-27 at the Shanghai World EXPO Exhibition & Convention Center. MIRTEC’s new machines have been developed under a concept, ‘Perfect Inspection Solution’. This is an inspection concept involving the combination of 3D, 2D, and side-camera inspection.
Parts & Supplies | Pick and Place/Feeders
square chip resistor 1608. 2012. 3216. 3225 (5025.6432 net work resistor (excluding SOP, SOJ, PLCC types) MELF resistor 1.6*1.0. 2.0*1.25 3.5*1.4. 5.9*2.2 Laminated ceramic capacitor 1608, 2012, 3216, 3225, 4532, 5750, (
Parts & Supplies | Assembly Accessories
Grease oil MGREAS400G0 OIL FILTER ELEMENT AFM30P-060S Oil Seal (TCV305011 ) AP1709A Oil Seal ( SC224211 ) AC1148A Metal foil low resistance chip resistors KRL2012E-C-R010-F-T1 Polyurethane coil tube UC-04-25
Technical Library | 2023-01-17 17:27:13.0
Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The degree of wetting, the microstructure (in particular the intermetallic layer), and the inherent strength of the solder all factor into the reliability of the solder joint. This paper presents experimental results on the effect of reflow profile on both 63%Sn 37%Pb (SnPb) and 96.5%Sn 3.0%Ag 0.5%Cu (SAC 305) solder joint shear force. Specifically, the effect of the reflow peak temperature and time above solder liquidus temperature are studied. Nine reflow profiles for SAC 305 and nine reflow profiles for SnPb have been developed with three levels of peak temperature (230 o C, 240 o C, and 250 o C for SAC 305; and 195 o C, 205 o C, and 215 o C for SnPb) and three levels of time above solder liquidus temperature (30 sec., 60 sec., and 90 sec.). The shear force data of four different sizes of chip resistors (1206, 0805, 0603, and 0402) are compared across the different profiles. The shear force of the resistors is measured at time 0 (right after assembly). The fracture surfaces have been studied using a scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS)
Technical Library | 2022-04-27 01:34:43.0
SMD capacitors and resistors have small sizes and many models. Some manufacturers buy a lot of products and do not use them up in time. The problem of storage is always a headache. So how should chip capacitors and resistors be stored? There are also precautions when using chip capacitors. Please see the following information and hope it will help you.
Training Courses | | | Other Courses
Other courses related to electronics manufacturing and assembly
Career Center | Middleboro, Massachusetts USA | Production
Highly motivated SMT Repair/ Assembly Operators needed for Contract Electronics Manufacturer. Duties include: repair and soldering of SMT and TH components, assembling of PCB's, and operation of automated production equipment. Experience using vario
Career Center | binan city, Laguna Philippines | Engineering,Maintenance,Technical Support
6.5 Years Experience in Semiconductor Industry Specializing in Dispensing process and Equipment. 5.0 Years of Experience in Field Service Engineering. Machine Commissioning / Customer support 24 / 7, Technical Support for Customer machine and process
Career Center | , District of Columbia | Engineering,Management,Production,Sales/Marketing
• Strong technical leadership and decision-making skills; strong verbal and written communication skills to provide clear, crisp direction for key issue resolution; and good team skills to facilitate cross-functional cross -site team effectiveness.
| https://www.smtfactory.com/How-to-replace-the-chip-capacitor-of-the-SAMSUNG-Pick-Place-Machine-id3532139.html
& Place Machine 's chip capacitor identification rules are partly similar to chip resistors. The difference is that the surface of the chip resistor will have parameter identification, but the surface of the chip capacitor does not have any parameter identification
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/sonoscan/support/application-notes
Plastic ICs/PEMs Flex Circuit Smart Card Bonded Wafers Chip Scale Package Flip Chip Hybrid Ceramic Solar Cells Packaging, Seals Materials Other Plastic ICs/PEMs
.gif)
winsouce.jpg)