FACTS²™ DF2400™ C‑SAM® Automated In-line Inspection Tool for Defect-Free Production Without Sacrificing Throughput The FACTS²™ delivers state-of-the-art, automated in-line inspection for quality and process control. Delivering high throughput wit
Electronics Forum | Tue Jul 31 18:49:20 EDT 2001 | arsmoriendi
i have a problem with some units that had one capacitor only soldered in one side, the geometry of the capacitor is 0805, our product during his life suffer a lot of stress (due temperature or vibration), some of those units are already with the cost
Electronics Forum | Mon Feb 24 11:02:42 EST 2003 | Claude_Couture
Every time this problem was brought to me, handling was the problem. Make sure to: 1- track the exact place the components are lost, i.e.: visually inspect the pcb before and after each step in your assembly line. 2- if step one does not pin point t
Industry News | 2018-10-18 09:37:27.0
How To Set Profile In SMT Reflow Oven
Industry News | 2018-12-13 03:35:05.0
Pick And Place Machine
Technical Library | 2019-11-15 02:20:26.0
Material Aging Test-UV Weathering Test Chamber 1.What is UV aging? UV aging chambers use fluorescent ultraviolet lamp as light source to simulate UV radiation and condensation in natural sunlight, and to carry out accelerated weather resistance test in order to obtain the result of weather resistance of the material. UV aging detection is widely used in non-metallic materials, organic materials (such as coatings, paints, rubber, plastics and their products) under the change of sunlight, humidity, temperature, condensation and other climatic conditions to test the aging degree and situation of related products and materials. 2.Why we should do UV aging test? When the product is placed in the ambient environment, there will be different problems taken place, such as appearance changes, including cracking, speckle, powdering or color change, and even performance degradation,which may be due to the loss of components in the resin resulting in chemical bonds changes inside the molecular structure, this is mainly caused by sunlight, industrial exclusion of waste gas, bacteria and so on. The aging performance of the product directly affects the lifespan of the product, so aging test become significant,non-metallic materials, organic materials (such as paints, paints, rubber, plastics and their products) are subject to changes in sunlight, humidity, temperature, condensation and other climatic conditions to test the degree and condition of aging of related products and materials. The natural aging test is to put the plastic specimen under the sun exposure, and it is directly under the natural climate environment,to test the material performance under various factors such as light, heat energy, atmospheric humidity, oxygen and ozone, industrial pollution and the like, the most harsh climate condition should be selected,or near the actual application area of the material, the test site shall be open and flat, no obstacle to affect the test results,the specimen holder shall be facing the equator and at an angle of 45 ° from the ground. When the main performance index of the specimen has been reduced, the test s/b terminated when it achieve the minimum allowable use value . in most case,the test is terminated when the product primary performance index falls to 50% of the initial value. The natural aging process is a very slow process, and there is a great difference in different geographical conditions, which brings difficulties to evaluate the aging resistance of the product. It is an attempt to make an evaluation of the aging performance of the plastic in a shorter time,that is accelerated aging test. The accelerated aging test can be used to simulate the human light source of the fluorescent lamp, including the carbon arc lamp, the xenon arc lamp and the fluorescent ultraviolet lamp, and the artificial light sources can generate more light than the natural sunlight on the ground. When these artificial light sources are used, it is also common to use the combination of the condenser to simulate the rain drop, the dew and the like to conduct the aging test on the product.
http://www.pcb-separator.com/html/PRODUCTS/PCB%20separator/2015/0607/137.html ?????????/V-cut depaneling/PCB Depanelers/??pcb????/PCB cutting machine/pcb depaneling machine/depanelizing pcb
http://www.pcb-separator.com/html/PRODUCTS/PCB%20separator/2015/0607/137.html ?????????/V-cut depaneling/PCB Depanelers/??pcb????/PCB cutting machine/pcb depaneling machine/depanelizing pcb
PCB Libraries, Inc. | https://www.pcblibraries.com/Forum/RSS_bga-chamfer_topic727.xml
. The silkscreen chamfer will fall under the part as created if the physical part does not have a chamfer. All BGA packages do not physically have a corner chamfer so this silkscreen will sometimes be under the component and not visible after assembly
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/sonoscan/support/imaging-modes
. This ceramic disk has been inspected using two types of imaging modes. With the Surface-Scan, the ultrasound directly reflected off of the surface is captured and the crack is evident
winsouce.jpg)
