New Equipment | ESD Control Supplies
Static Solutions, Inc. heel grounders are specially designed to provide a continuous ground path between the user and a properly grounded ESD safe floor. Our heel grounders are designed to drain the static charge of a user that is built up during nor
New Equipment | ESD Control Supplies
High performance fluxophobic stencil treatments wipes Enhance your stencil performance in seconds! Aculon is pleased to announce the launch of their latest generation of stencil coating technology. Aculon’s proprietary technology treats the undersi
Electronics Forum | Tue Aug 11 09:52:53 EDT 2015 | rgduval
I assume that these parts are falling off during second-side reflow? The easy solution, of course, is to not build high-mass components on first-side reflow. If this isn't practical, however, you can try using epoxy/glue under the component. We'
Electronics Forum | Mon Dec 03 15:03:49 EST 2018 | dleeper
I can't open your spread sheet to see how you calculate this, but usually this sort of calculation assumes the leads are spaced symmetrically on both sides of the part and the center of mass is between them. Gravity pulls the part down, while the wet
Industry News | 2003-03-31 09:31:11.0
Electronic contract manufacturers face tough realities
Industry News | 2018-12-08 03:35:10.0
Top 10 Consumer Electronics Companies in the World
Parts & Supplies | Repair/Rework
PG-P6860 Main Features： 1、 The top heater can move freely along the X, Y axis in the IR preheating area. It is good for many BGA chips distribution at different positions in the PCB board which need repair. X-shaped infrared laser can do rapid lo
Parts & Supplies | Repair/Rework
PG-P6800 Main Features： 1、There are 3 independent heaters. The 1st and 2nd hot-air heaters can control multiple groups and segments temperature parameters. The 2nd heater can move up and down. The 3rd large area IR heater can preheat the PCB boar
Technical Library | 2023-08-14 09:06:53.0
In the operation of SMT mounter, the process and integrity of the nozzle of the mounter will have a significant impact on the performance of the machine. As one of the important components of the SMT machine, it is necessary for us to carry out daily maintenance and upkeep of the SMT nozzle. To ensure that the suction nozzle of the SMT machine is intact before operation, how should we do a good job of maintaining the suction nozzle of the SMT machine during normal use? KINGSUN technical team analysis operation has the following main points: 1.Wipe the surface of the SMT nozzle with a dust-free cloth. 2.The small aperture nozzle can be passed through with a thin steel wire and then blown with an air gun. 3.The surface of the nozzle should not be soaked with corrosive solution such as alcohol, as this may cause the surface to fall off. 4.HOLDER should use a cotton swab to wipe the cavity and not damage the filter screen. 5.Regular addition of special grease to HOLDER claws. 6.According to production, it is best to regularly maintain and do other maintenance regularly. (* Suitable for Yamaha SMT machine nozzles , JUKI SMT machine nozzles, Samsung SMT machine nozzles, Panasonic SMT machine nozzles, Fuji SMT machine nozzles, Siemens SMT machine nozzles etc.) Regarding the SMT machine nozzle daily maintenance operation instructions, KINGSUN share with you here , hoping to be helpful to you. More information about Products please Contact US at jenny@ksunsmt.com or visit www.ksunsmt.com , thanks.
http://www.pcb-separator.com/html/PRODUCTS/PCB%20separator/2015/0607/137.html ?????????/V-cut depaneling/PCB Depanelers/??pcb????/PCB cutting machine/pcb depaneling machine/depanelizing pcb
http://www.pcb-separator.com/html/PRODUCTS/PCB%20separator/2015/0607/137.html ?????????/V-cut depaneling/PCB Depanelers/??pcb????/PCB cutting machine/pcb depaneling machine/depanelizing pcb
| https://www.eptac.com/faqs/ask-helena-leo/ask/charring-of-wire-insulation
. The charring means the insulation has been burnt and the burnt material is left behind. This charring is carbon and conductive, so depending upon how secure it is to the wire, it can fall off and create a short
ASCEN Technology | https://www.ascen.ltd/Video_Channel/PCB_depaneling_machine/1072.html
device.the separator can fastening the V-cut during the PCB depaneling.don't need worry about the PCB piece fall off the V-cut,don't need worry about the PCB
winsouce.jpg)
