Industry Directory | Consultant / Service Provider
Elmet LLC is an accredited lab, primarily providing cross sectioning of circuit boards, visual and x-ray inspections of PCBAs and other metallographic and metallurgical services including SEM examination and EDS analysis.
Industry Directory | Manufacturer
Buyers of Scrap Materials and Surplus Machinery, Equipment and Inventories Precious Metal Refining Warehouse Liquidation PCB & Electronic Scrap Recycling Purchasing of Used Surplus Semiconductor
Our range of connector gaskets includes precision diecut gaskets made from a large selection of materials, both conductive and non-conductive. The DC Series comprises waveguide and connector gaskets to MIL-C-81511, MIL-C-5015, MIL-C-38999 and MIL-C-
Our experienced engineers will design an electro/mechanical solution to interface between your product and your test instruments. Circuit Check develops hot mock-up and custom stand-alone functional tests for circuit cards, backplane boards and card
Electronics Forum | Wed Jun 27 14:36:22 EDT 2012 | cyber_wolf
If the X axis is moving then maybe your Elmo is not adjusted correctly. There is a procedure to adjust it in the manual(assuming you have the original manual). The correct location is XGTS which is a white connector on the booster. The fans are 24V
Electronics Forum | Wed Jun 27 13:38:56 EDT 2012 | upguy
Thanks for the information and insights. Our booster is probably getting too hot, even with AC. There is bouncing when we trim component locations. Every so often, while trimming component locations, the x-axis will start to slowly move away (by i
Used SMT Equipment | General Purpose Equipment
Year 2008 - Like New Condition Tyco SEP 3T Shuttle Electric Press Standalone electric press for the application of PCBs onto compliant pin housings or connectors • Servo electric press with shuttle system for product location under press ram • Ho
Used SMT Equipment | Adhesive Dispensers
This adhesive dispense system has been installed in a custom gantry that can be set on a bench. The height of the gantry allows it to dispense onto unusually tall pieces. It is in fully operational condition. It comes with all of the following: Com
Industry News | 2003-07-08 09:22:20.0
A new range of coding profiles for Combicon wire-to-board connectors aims to avoid the pitfalls of inserting the wrong plug into a header when making plug-in connections to a PCB.
Industry News | 2018-01-15 13:37:11.0
The SMTA is pleased to announce the Best Papers from SMTA International 2017. As speakers at SMTA International, individuals make contributions to the industry by sharing their research and findings. For these exceptional achievements, a cash award and plaque are given to all winners.
.png)
Parts & Supplies | Assembly Accessories
JUKI full series of general, image display LCD, JUKI750 760 2010 2020 2050 2060 original displays for CRT old display, easy to damage. Direct replacement for liquid crystal displays, no fever, green environmental protection save electricity, LCD disp
.jpg)
Parts & Supplies | Pick and Place/Feeders
03090055S01 Pulse counter CUB7CCS0 8-digit 03090079-01 cover fan protective grid 03090149-01 PCB Power adjust HCS II cpl. 03090669-01 replacement pin, multiframe splice 2,5mm 03090670-01 replacement pin, multiframe splice 2,0mm 03090712-01 Stop-
Technical Library | 2019-06-06 00:19:02.0
More and more people and things are using electronic devices to communicate. Subsequently, many electronic products, in particular mobile base stations and core network nodes, need to handle enormous amounts of data per second. One important link in this communication chain is high speed pressfit connectors that are often used to connect mother boards and back planes in core network nodes. These new high speed pressfit connectors have several hundreds of thin, short and weak pins that are prone to damage. Small variations in via hole dimensions or hole plating thickness affect the connections; if the holes are too small, the pins may be bentor permanently deformed and if the holes are too large they will not form gas tight connections.The goal of this project was to understand how rework of these new high speed pressfit connectors affects connection strengths, hole wall deformations and plating cracks.
Technical Library | 2016-05-19 16:03:37.0
As consumers become more reliant on their handheld electronic devices and take them into new environments, devices are increasingly exposed to situations that can cause failure. In response, the electronics industry is making these devices more resistant to environmental exposures. Printed circuit board assemblies, handheld devices and wearables can benefit from a protective conformal coating to minimize device failures by providing a barrier to environmental exposure and contamination. Traditional conformal coatings can be applied very thick and often require thermal or UV curing steps that add extra cost and processing time compared to alternative technologies. These coatings, due to their thickness, commonly require time and effort to mask connectors in order to permit electrical conductivity. Ultra-thin fluorochemical coatings, however, can provide excellent protection, are thin enough to not necessarily require component masking and do not necessarily require curing. In this work, ultra-thin fluoropolymer coatings were tested by internal and industry approved test methods, such as IEC (ingress protection), IPC (conformal coating qualification), and ASTM (flowers-of-sulfur exposure), to determine whether this level of protection and process ease was possible.
These are the instructions for the BEST Heatshields(TM) an effective, high tech simple way to shield heat sensitive components during reflow/rework. This ceramic-based non-woven material, when properly deployed, will protect components so that they d
Training Courses | | | IPC-A-610 Trainer (CIT)
The Certified IPC-A-610 Trainer (CIT) courses recognize individuals as qualified trainers in the area of quality assurance of electrical and electronic assemblies and prepares them to deliver Certified IPC-A-610 (CIS) training.
Training Courses | | | IPC-A-610 Trainer (CIT)
The Certified IPC-A-610 Trainer (CIT) courses recognize individuals as qualified trainers in the area of quality assurance of electrical and electronic assemblies and prepares them to deliver Certified IPC-A-610 (CIS) training.
Career Center | Gwinnett County, Georgia USA | Production
SHIFTS: 1st and 2nd Shifts (Over-Time as required) STATUS: Indefinite Temporary PAY: $11.00-$12.00 per hour JOB DESCRIPTION • Perform SMT soldering, desoldering, rework, and assembly of fine pitch electronic components on Printed Circuit Boards (PCB
Advanced Electronic Connector Technologies News Forums SMT Equipment Company Directory Calendar Career Center Advertising About FREE Company Listing! Advanced Electronic Connector Technologies Military electrical connectors have
Advanced Electronic Connector Technologies News Forums SMT Equipment Company Directory Calendar Career Center Advertising About FREE Company Listing! Advanced Electronic Connector Technologies Military electrical connectors have
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/dage/test-types-2020/connectors
Connector testing X-Ray Inspection and Test Products Corporate | Global Directory | Languages Division Only All of Nordson Home Products Bondtesting Systems Micro Materials Testing Wafer Inspection and Metrology X-ray Inspection Systems X-ray Counting Systems Applications Battery
1st Place Machinery Inc. | http://www.firstplacemachinery.com/firstplace_tyco_connector_press.html
Tyco Connector Press Tyco SEP 3T Shuttle Electric Press Year 2008 - Like New Condition Standalone electric press for the application of PCBs onto compliant pin housings or connectors
