Industry Directory | Manufacturer
Sikama International designs, develops, manufactures and markets reflow solder furnaces/curing systems, featuring our patented conduction+convection heating and cooling technology. Our furnaces are designed for efficient use of power and gas.
PCB separating Routing Machine with high precision shaft system can move quickly for cutting or separate the PCB printed circuit board,increase productivity while maintaining high accuracy. If you want know how to choose the best PCB separator for
PCB Depaneling Router with high precision shaft system can move quickly for cutting or separate the PCB printed circuit board,increase productivity while maintaining high accuracy. If you want know how to choose the best PCB separator for your PCB
Used SMT Equipment | Soldering - Reflow
10 zone reflow oven with superior water cooling - plenty of cooling for lead free Edge/Mesh combo conveyor Water cooled for superior cooling, chillers available Chain oilers Dual cooling section Left to right transfer Facilit
Used SMT Equipment | Soldering - Reflow
Mesh conveyor Top and bottom heaters (newer heaters) Cooling section Newer Blowers
Industry News | 2016-06-27 14:59:09.0
GPD Global introduces the NEW TempView Thermal Imaging System that ensures the success of heated dispensing processes like Underfill, Encapsulations, Dam and Fill, and more. The TempView Thermal Imaging System monitors the temperature of the entire substrate for complete heat profile characterization. Regions of the product may be selected for monitoring during the heating process. Now you can accurately monitor temperature of specific devices to be sure they are up to temperature before starting a process.
Industry News | 2022-11-11 07:33:41.0
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board pads.
Technical Library | 2019-12-12 02:43:44.0
Today we discuss the reason that causes temperature humidity chamber to alarm,In most cases, the equipment alarm is caused by the improper operation in the process of use, which mainly includes following reasons:that are refrigeration system, temperature system and circulating system. First, Refrigeration system 1, refrigeration compressor overpressure alarm. If the refrigerant pressure exceeds the set value, it will stop and alarm at the same time. At this time, the fault must be eliminated and then manually reset. 2, short phase power supply, phase sequence alarm. When the external power supply of the equipment is out of phase or the phase sequence is changed, it will stop and alarm at the same time. 3. The circulating cooling water is short of water to alarm. When the water pressure of the cooling circulating water system is insufficient, it will stop and alarm at the same time, and it must wait for the fault to be eliminated and reset at the same time before it could run normally. 4, refrigeration compressor overheating alarm. When the coil of the compressor is overheated and the power supply of the line is not normal, it will stop and alarm at the same time. Second, Temperature system 1, the overtemperature alarm in the chamber. The sensors in the channel and the sample area are equipped with overtemperature protection devices, and there are also overtemperature protecter on the control panel. When the temperature in the working chamber exceeds the setting value on the controller, it will stop and alarm. 2. sample overtemperature protection. When the temperature in the sample area exceeds the protection temperature set by the controller, it will stop and alarm at the same time. The overtemperature protection of the sample is divided into upper limit protection and lower limit protection, which can be set according to the demand, Third,Circulating system 1. The alarm is caused by the overheating of the circulating fan. When the coil of the fan is over-heated, the alarm will be stopped at the same time. 2. The fan over-current alarm. When the current of the fan exceeds the allowable value, the alarm is stopped at the same time, and the normal operation can only be carried out after the fault maintenance of the overcurrent is completed. This is what we talk about today,if you have more questions,let us know.
Lead Free SMT Reflow Oven XMR-1000D Product features: ▶fully meet all kinds of lead-free welding process requirements. ▶WindowsXP operating system, English and Chinese interface, easy to learn operation; Standard air furnace, patented hot air system
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board
| http://etasmt.com/cc?ID=te_news_bulletin,21161&url=_print
. The cooling rate will affect the strength of the solder joint. In this section, the lead-tin powder in the solder paste has melted and fully wetted the surface to be connected
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/polymer-processing-systems/information/optimize-your-barrel-temperatures
) between pellet to pellet, and (3) between the root of the screw and the plastic pellet. Screw cooling on the screws' feed section core should always be installed
