Electronics Forum | Thu Jun 29 11:08:55 EDT 2000 | Dave F
Kok Han: Good to hear from you. Please help us understand you situation better by talking more about: � Component IC of the RF unit (IC101). For instance: SMT / PTH, package, pitch, lead material, lead finish, package type, package weight, coplan
Electronics Forum | Fri Jun 24 07:02:35 EDT 2005 | davef
Problem 1: Solder shortage * Stencil aperatures [except the heat slug] should be 1:1 with the board. * Stencil should be 5 thou thick laser cut. * Board should be 1:1 with the component * Print should look good. Problem #2: Bad connection between p
Industry News | 2018-10-18 10:24:05.0
The Design Principles of Stencil Apertures
Industry News | 2003-08-27 10:58:00.0
Lead free solders and embedded passives headline professional development schedule at the 2003 IPC Annual Meeting
Technical Library | 2010-05-27 22:12:10.0
The quad flat pack no lead or quad flat non-leaded (QFN) is one of the fastest growing package types in the electronics industry today. While the advantages of QFNs are well documented, concerns arise with its reliability and manufacturability. Acceptance of this package, especially in long-life, severe-environment, high-reliability applications, is currently limited. One of the most common drivers for reliability failures is inappropriate adoption of new technologies, such as the case with QFN. In this presentation, we will review and discuss QFN related reliability concerns and challenges, and propose Physics-of-Failure (PoF) based approaches to allow the confident introduction of QFN components into electronics products.
Technical Library | 2018-05-23 12:12:43.0
Driven by miniaturization, cost reduction and tighter requirements for electrical and thermal performance, the use of lead-frame based bottom-termination components (LF-BTC) as small-outline no-leads (SON), quad-flat no leads (QFN) packages etc., is increasing. However, a major distractor for the use of such packages in high-reliability applications has been the lack of a visible solder (toe) fillet on the edge surface of the pins: because the post-package assembly singulation process typically leaves bare copper leadframe at the singulation edge, which is not protected against oxidation and thus does not easily solder-wet, a solder fillet (toe fillet) does not generally develop.
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
PCB Dynamic Coplanarity At Elevated Temperatures PCB Dynamic Coplanarity At Elevated Temperatures iNEMI's SMTAI 2011 presentation by: John Davignon, Ken Chiavone, Jiahui Pan, James Henzi, David Mendez, Ron Kulterman; Intel Corporation
Minimizing Voiding In QFN Packages Using Solder Preforms SMTnet Express July 27, 2012, Subscribers: 25333, Members: Companies: 8933, Users: 33366 Minimizing Voiding In QFN Packages Using Solder Preforms First published in the 2012 IPC APEX EXPO
Surface Mount Technology Association (SMTA) | https://www.smta.org/knowledge/journal.cfm
Influence of Alloy Composition and Temperature Cycling Dwell Time on the Reliability of a Quad Flat No Lead (QFN) Package Richard Coyle, Peter Read, Heather McCormick, Richard Popowich, and Debra Fleming Abstract 2011 24-4 Comparison Of Several PCB Final
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/07/last-will-of-bga-void.pdf
, “The Effects of Non-filled Microvia in Pad on Pbfree Solder Joint Reliability of BGA and QFN Packages in Accelerated Thermal Cycling
.gif)
winsouce.jpg)
