New Equipment | Education/Training
IPC A-600H Acceptability of Electronic Assemblies. The IPC-A-600, "Acceptability of Printed Boards " is the most widely used published specification on printed wiring boards. This specification has set the standard for rigid printed boards in terms o
New Equipment | Solder Materials
NC275B Liquid Flux is a water-based VOC-Free flux that has performance and reliability characteristics equal or superior to many alcohol-based fluxes. A medium-solids/residue flux, NC275B can be used with all common lead-free wave soldering alloys in
Electronics Forum | Sat Jun 11 07:51:15 EDT 2016 | davef
Hi Steve ... There are arguments between fabricators and thermal relievers about adding non-connected copper tabs to barrels in hopes of providing thermal relief, but that's not what you're talking about, I believe. I don't foresee an issue moving t
Electronics Forum | Fri Jan 07 09:03:44 EST 2022 | jineshjpr
Hi Everyone, I want to understand what is the copper thickness to be maintained in PTH Barrel hole. Is this same as Fab recommendation of surface finished copper thickness like 25/35/70 microns..??? Is there any specific IPC standards available to un
Industry News | 2016-04-18 11:30:07.0
Kester will be represented through our German sales partners, ADL Prozesstechnik UG (booth # 7-426) and EURO TOOL GmbH (booth # 7-520), at SMT Hybrid Packaging 2016, which will take place April 26-28 at the Exhibition Centre in Nuremberg, Germany.
Industry News | 2020-12-10 14:18:13.0
IP Rated Spring-Loaded DIP Pins from Adam Tech Interconnects Prevent Moisture from Entering the Pin around Barrel Seams
Technical Library | 2015-12-23 16:57:27.0
The onset of copper barrel cracks is typically induced by the presence of manufacturing defects. In the absence of discernible manufacturing defects, the causes of copper barrel cracks in printed circuit board (PCB) plated through holes is not well understood. Accordingly, there is a need to determine what affects the onset of barrel cracks and then control those causes to mitigate their initiation.The objective of this research is to conduct a design of experiment (DOE) to determine if there is a relationship between PCB fabrication processes and the prevalence of fine barrel cracks. The test vehicle used will be a 16-layer epoxy-based PCB that has two different sized plated through holes as well as buried vias.
Technical Library | 2021-07-20 20:02:29.0
During the manufacturing of printed circuit boards (PCBs) for a Flight Project, it was found that a European manufacturer was building its boards to a European standard that had no requirement for copper wrap on the vias. The amount of copper wrap that was measured on coupons from the panel containing the boards of interest was less than the amount specified in IPC-6012 Rev B, Class 3. To help determine the reliability and usability of the boards, three sets of tests and a simulation were run. The test results, along with results of simulation and destructive physical analysis, are presented in this paper. The first experiment involved subjecting coupons from the panels supplied by the European manufacturer to thermal cycling. After 17 000 cycles, the test was stopped with no failures. A second set of accelerated tests involved comparing the thermal fatigue life of test samples made from FR4 and polyimide with varying amounts of copper wrap. Again, the testing did not reveal any failures. The third test involved using interconnect stress test coupons with through-hole vias and blind vias that were subjected to elevated temperatures to accelerate fatigue failures. While there were failures, as expected, the failures were at barrel cracks. In addition to the experiments, this paper also discusses the results of finite-element analysis using simulation software that was used to model plated-through holes under thermal stress using a steady-state analysis, also showing the main failure mode was barrel cracking. The tests show that although copper wrap was sought as a better alternative to butt joints between barrel plating and copper foil layers, manufacturability remains challenging and attempts to meet the requirements often result in features that reduce the reliability of the boards. Experimental and simulation work discussed in this paper indicate that the standard requirements for copper wrap are not contributing to the overall board reliability, although it should be added that a design with a butt joint is going to be a higher risk than a reduced copper wrap design. The study further shows that procurement requirements for wrap plating thickness from Class 3 to Class 2 would pose little risk to reliability (minimum 5 μm/0.197 mil for all via types).Experimental results corroborated by modeling indicate that the stress maxima are internal to the barrels rather than at the wrap location. In fact, the existence of Cu wrap was determined to have no appreciable effect on reliability.
This video describes the IPC A-600 training and certification program. The IPC A-600 specification is a set of acceptability specifications for printed circuit boards. These standards determine the acceptance and reject criteria for printed wiring bo
This video describes the IPC A-600 training and certification program. The IPC A-600 specification is a set of acceptability specifications for printed circuit boards. These standards determine the acceptance and reject criteria for printed wiring bo
Training Courses | | | Other Courses
Other courses related to electronics manufacturing and assembly
SMTnet Express, December 23, 2015, Subscribers: 23,927, Members: Companies: 14,845, Users: 39,621 PCB Fabrication Processes and Their Effects on Fine Copper Barrel Cracks Edward Arthur, Charles Busa, Melissa Durfee, Chad Gibson, Wade Goldman P
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/select/soldering-processes/selective-soldering-workshops
construction including copper layers, barrel plating and porosity. The interaction between the PCB and the selective soldering process and heat flow characteristics within thermally challenging multi-layer boards will be defined
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/RSS_component-leads-too-short_topic1789.xml
? Id the barrel ofthe hole tied to any type of a copper plane? If so, are there thermalrelief pads? Is it mission critical?
