Industry Directory | Consultant / Service Provider / Training Provider
ERI is a specialized engineering school, focusing on the reliability and durability of hardware, upon the kinds of stresses that can shorten the life of hardware such as yours and upon appropriate tests to uncover weaknesses.
New Equipment | Cleaning Agents
LONOX® L5611 is a solvent-based cleaner for misprinted boards and stencils. It is effective on a wide variety of flux, solder paste and uncured adhesives. Easy to use, L5611 is intended to be diluted with water and effective at ambient temperature t
New Equipment | Cable & Wire Harness Equipment
Overview The STS 1100 tinning station is designed for fluxing and lead-free tin coating of stripped wire ends with cross sections up to 2.5 mm² (14 AWG) and tinning lengths up to 5 mm (0.2''). Optionally, wire ends with cross sections up 4 mm² (12 A
Electronics Forum | Wed Jul 07 09:47:41 EDT 1999 | Peter Brant
| | Q #1) Is it more reliable to have the mask tent over the vias or risk getting vias half filled with solder? These are vias with an .020" hole and .040" or .050" pad. WIth regards to this question, and scott's follow up, I have used the "epoxy me
Electronics Forum | Wed Feb 01 18:11:43 EST 2006 | Chris
I wonder if they are concerned about getting chemicals trapped in the tented vias. If the tented vias have pin hole openings or even larger openings, chemicals from the ENIG process could become entrapped in the via holes and not washed away in the
Industry News | 2014-09-18 17:55:32.0
SMTA China announcing that it presented awards for nine papers at the SMTA China South 2014 Conference Award Presentation Ceremony, held on Tuesday, August 26, 2014 at Shenzhen Convention & Exhibition Center in conjunction with the SMTA China Annual Award Ceremony.
Industry News | 2020-01-20 16:42:42.0
The IPC APEX EXPO 2020 best technical conference papers in the domestic and international categories have been selected; the paper authors will receive their awards during the opening keynote session on Tuesday, February 4, 2020.
Technical Library | 2023-01-10 20:15:42.0
Over the past years there has been consistent growth in the use of electroless nickel / immersion gold (ENIG) as a final finish. The finish is now frequently being used for PBGA, CSP, QFP and COB and more recently gathered considerable interest as a low cost under-bump metallization for flip chip bumping application. One of the largest users for this finish has been the telecommunication industry, were millions of square meters of PCBs with ENIG have been successfully used. The nickel layer offers advantages such as multiple soldering cycles and hand reworks without copper dissolution being a factor. The nickel also acts as a reinforcement to improve through-hole and blind micro via thermal integrity. In addition the nickel layer offers advantages such as co-planarity, Al-wire bondability and the use as contact surface for keypads or contact switching. Especially those pads, which are not covered by solder need a protective coating in corrosive environment – such as high humidity or pollutant gas.
DescriptionThe Electrovert® Electra™ is an advanced, meticulously engineered wave soldering system designed for high-mass and high-volume manufacturers. Although intended for maximum throughput requirements, the Electra also offers maximum process fl
Training Courses | | | Other Courses
Other courses related to electronics manufacturing and assembly
Events Calendar | Mon Apr 23 00:00:00 EDT 2018 - Thu Apr 26 00:00:00 EDT 2018 | Shanghai, China
SMTA China East Conference 2018
SMTnet Express, May 10, 2018, Subscribers: 31,023, Companies: 10,930, Users: 24,698 Relative Humidity Dependence of Creep Corrosion on Organic-Acid Flux Soldered Printed Circuit Boards Haley Fu, iNEMI Creep corrosion on printed circuit boards
SMTnet Express, November 10, 2016, Subscribers: 26,5620, Companies: 15,019, Users: 41,389 Corrosion Resistant Servers for Free-Air Cooling Data Centers Qiujiang Liu; Baidu, Inc., Prabjit Singh; IBM Corporation This paper describes a corrosion
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/polymer-processing-systems/information/barrel-materials
. Bimetallic - Corrosion Resistant The corrosion resistant grades are usually nickel/cobalt based materials. They give improved chemical resistance but sacrifice some wear resistance. Xaloy ® X-306 ®
40731 | https://www.smta.org/harsh/Harsh-Environments-Conference-Program-2020.pdf
Surface Mount Technology Association (SMTA)
