Industry Directory | Manufacturer
Rogers' high performance laminates and bondplies are engineered to meet stringent customer requirements for 5G wireless communication, wired infrastructure, automotive radar sensors, aerospace, satellites and more.
New Equipment | Rework & Repair Equipment
BGA Rework Stations from the BGA Experts with over 25 years rework process experience and customer support! For high volume BGA Rework on even the largest computer and networking boards! The model SV560A has a high resolution optical system for pla
Low Cost Punch For Singulation Small Tab Routed Panels N200 singulates one tab at a time with upper and lower pinch blades. Singulate curve routed and odd shaped boards. Top and bottom knife set cuts tabs cleanly. Minimal stress on PCB. Toolin
Electronics Forum | Fri Nov 09 01:41:04 EST 2007 | reypal
Thank You Guys for all your input. The reason I raised this case that it was our customer challenge us on the physical outlook of the profile board rather than its functionality no matter the profile curves looks good. Yes, we have a procedure to de
Electronics Forum | Thu Sep 23 14:41:48 EDT 1999 | Doug Philbrick
| Hiya, | | Could anyone please suggest recommended manufacturers of | IR rework stations for the removal of various SMT comps. | | Cheers | I have 2 customers who went from hot air system to a PDR and they love it. The system will give them a ni
.jpg)
Used SMT Equipment | Pick and Place/Feeders
FUJI/NXTIIC Used Chip Mounter The Fuji NXT is designed to meet the demands of modern production environments. Its interchangeable placement heads allow each machine module to function as either a high speed chip counter or a multi-function placemen
Used SMT Equipment | SMT Equipment
Baking SMT on a cheap kitchen toaster oven is not difficult. You just need some patience and exploration good will. In this page you will read the manual procedure to bake SMD boards into a regular kitchen toaster oven appliance. Follows information
Industry News | 2003-05-06 09:05:12.0
New Schematic Capture and Simulation Software Delivers Innovative Features and the Industry�s Best Price/Performance
Industry News | 2018-10-18 09:14:05.0
Lead-free processes propose new requirements on reflow soldering quality
Parts & Supplies | Repair/Rework
PG-P6800 Main Features： 1、There are 3 independent heaters. The 1st and 2nd hot-air heaters can control multiple groups and segments temperature parameters. The 2nd heater can move up and down. The 3rd large area IR heater can preheat the PCB boar
Parts & Supplies | Repair/Rework
. This machine adopts industrial computer control, full automatic vision alignment system can acquire BGA and the PCB image through the CCD camera and collect them on the image positioning processing system, calculate the offset position and angle th
Technical Library | 2017-10-19 01:17:56.0
Wetting balance testing has been an industry standard for evaluating the solderability of surface finishes on printed circuit boards (PCB) for many years. A Wetting Balance Curve showing Force as a function of Time, along with the individual data outputs "Time to Zero" T(0), "Time to Two-Thirds Maximum Force" T(2/3), and "Maximum Force" F(max) are usually used to evaluate the solderability performance of various surface finishes. While a visual interpretation of the full curve is a quick way to compare various test results, this method is subjective and does not lend itself readily to a rigorous statistical evaluation. Therefore, very often, when a statistical evaluation is desired for comparing the solderability between different surface finishes or different test conditions, one of the individual parameters is chosen for convenience. However, focusing on a single output usually doesn't provide a complete picture of the solderability of the surface finish being evaluated.In this paper, various models here-in labeled as "point" and "area" models are generated using the three most commonly evaluated individual outputs T(0), T(2/3), and F(max). These models have been studied to quantify how well each describes the full wetting balance curve. The solderability score (S-Score) with ranking from 0 to 10 were given to quantify the wetting balance curve as the result of the model study, which corresponds well with experimental results.
Technical Library | 2009-04-22 21:13:19.0
An optimal reflow profile is one of the most critical factors in achieving quality solder joints on a printed circuit board (PCB) assembly with surface mount components. A profile is a function of temperatures applied to the assembly over time. When graphed on a Cartesian plane, a curve is formed that represents the temperature at a specific point on the PCB, at any given time, throughout the reflow process.
Low Cost Punch For Singulation Small Tab Routed Panels N200 singulates one tab at a time with upper and lower pinch blades. Singulate curve routed and odd shaped boards. Top and bottom knife set cuts tabs cleanly. Minimal stress on PCB. Toolin
Training Courses | | | ESD Control Training Courses
Browse training and certification programs for electrostatic discharge (ESD) control in electronics assembly.
Career Center | Dargaha Road Zameen Pallavaram Chennai, Tamilnadu India | Maintenance,Technical Support
CURRENT JOB: • Responsible for four sub department as Production support, Preventive maintenance activity, Spare parts control and NPI (New product Introduction) under one Equipment department. • Take care of OEE (Overall Equipment Efficiency), MTTR
Career Center | , Texas | Human Resources,Maintenance,Management,Technical Support
Over 17 years in the training and development industry.� I have a track record of successes in designing strategic programs that address organizational skill gaps and business initiatives. Being an expert in Instructional Systems Design (ISD) I have
SMTnet Express, November 19, 2017, Subscribers: 30,938, Companies: 10,768, Users: 23,942 To Quantify a Wetting Balance Curve Frank Xu Ph.D., Robert Farrell, Rita Mohanty Ph.D.; Enthone Wetting balance testing has been an industry standard
SMTnet Express, September 14, 2017, Subscribers: 30,799, Companies: 10,725, Users: 23,800 The Relationship Between Energy-Resource Depletion, Climate Change, Health Resources and the Environmental Kuznets Curve: Evidence From the Panel of Selected
Imagineering, Inc. | https://www.pcbnet.com/blog/how-can-a-printed-circuit-board-help-you-test-a-circuit-board-schematic/
. Polarized capacitors get a curved plate to represent the cathode and a plus sign to represent the positive pin. Inductors show up on a circuit board schematic as curved bumps, looped coils, and/or filled rectangles
FKN Systek | http://fknsystek.com/N%20Series.htm
The N200 is designed to singulate one tab at a time in low volume applications. Ideal where curved board contours or small routing dimensions make the use of the N100 problematic
winsouce.jpg)
.gif)