Industry Directory | Manufacturer
XPCB is a PCB manufacturer with superior expertise in multilayer rigid-flex PCB and flex PCB, supporting special technology including VIPPO, stacked vias, buried vias, blind vias, unsymmetrical structure, and air gap structure.
New Equipment | Education/Training
Blackfox’s Lead Free Soldering series minimizes the risks of conversion, and gives you the confidence to introduce lead free products and services quickly, with highest quality. The lead free certification program offers the latest requirements for S
New Equipment | Education/Training
IPC standards, the results of industry consensus and collaboration, are respected throughout the whole world. Using IPC standards allows manufacturers, customers and suppliers to speak the same language. IPC standards are used by the electronics
Electronics Forum | Wed Oct 09 14:15:56 EDT 2002 | slthomas
Pardon the cross-post from the design board....I thought maybe I should query both populations. Is anyone out there aware of any standard or even a section of a standard that specifically addresses design guidelines for two-sided assemblies, particu
Electronics Forum | Wed Oct 09 11:59:56 EDT 2002 | slthomas
Is anyone out there aware of any standard or even a section of a standard that specifically addresses design guidelines for two-sided assemblies, particularly one that focuses on different processes? I'm being asked to produce information from said
Used SMT Equipment | In-Circuit Testers
Yokogawa PZ4000 253710-D-M3 Power Analyzer The Yokogawa PZ4000 (253710) lets you make high-precision measurements of voltage, current, and consumed power in equipment driven at frequencies ranging from several tens of kHz to approximately 100 k
Industry News | 2003-02-13 08:11:45.0
eSight Can Reduce Time-to-manufacture and Time-to-market by as Much as 80%
Industry News | 2003-04-08 14:01:01.0
Sparton's design engineering team is one of 265 worldwide members in the Motorola Design Alliance program.
Technical Library | 2023-07-25 16:50:02.0
Some of the new handheld communication devices offer real challenges to the paste printing process. Normally, there are very small devices like 01005 chip components as well as 0.3 mm pitch uBGA along with other devices that require higher deposits of solder paste. Surface mount connectors or RF shields with coplanarity issues fall into this category. Aperture sizes for the small devices require a stencil thickness in the 50 to 75 um (2-3 mils) range for effective paste transfer whereas the RF shield and SMT connector would like at least 150 um (6 mils) paste height. Spacing is too small to use normal step stencils. This paper will explore a different type of step stencil for this application; a "Two-Print Stencil Process" step stencil. Here is a brief description of a "Two-Print Stencil Process". A 50 to 75 um (2-3 mils) stencil is used to print solder paste for the 01005, 0.3 mm pitch uBGA and other fine pitch components. While this paste is still wet a second in-line stencil printer is used to print all other components using a second thicker stencil. This second stencil has relief pockets on the contact side of the stencil any paste was printed with the first stencil. Design guidelines for minimum keep-out distances between the relief step, the fine pitch apertures, and the RF Shields apertures as well relief pocket height clearance of the paste printed by the first print stencil will be provided.
Technical Library | 2016-04-08 01:19:52.0
PCB assembly designs become more complex year-on-year, yet early-stage form/fit compliance verification of all designed-in components to the intended manufacturing processes remains a challenge. So long as librarians at the design and manufacturing levels continue to maintain their own local standards for component representation, there is no common representation in the design-to-manufacturing phase of the product lifecycle that can provide the basis for transfer of manufacturing process rules to the design level. A comprehensive methodology must be implemented for all component types, not just the minority which happen to conform to formal packaging standards, to successfully left-shift assembly and test DFM analysis to the design level and thus compress NPI cycle times.(...)This paper will demonstrate the technological components of the working solution: the logic for deriving repeatable and standardized package and pin classifications from a common source of component physical-model content, the method for associating DFA and DFT rules to those classifications, and the transfer of those rules to separate DFM and NPI analysis tools elsewhere in the design-through-manufacturing chain resulting in a consistent DFM process across multiple design and manufacturing organizations.
IPC Vice President David Bergman explains where to find and how to use the Document Revision Table.
Training Courses | | | PCB Design Courses
The PCB design courses teach students the process, techniques and tools needed to design layout of printed circuit boards.
Training Courses | | | PCB Design Courses
The PCB design courses teach students the process, techniques and tools needed to design layout of printed circuit boards.
Events Calendar | Thu Jun 08 00:00:00 EDT 2023 - Thu Jun 08 00:00:00 EDT 2023 | ,
SMTA Workforce Development Webinar: PCB Design Courses and Careers in PCB Design
Events Calendar | Tue Jul 11 00:00:00 EDT 2023 - Tue Jul 11 00:00:00 EDT 2023 | Oshkosh, Wisconsin USA
Wisconsin Chapter In-Person Event: PCB Workshop and PCB Plant Tour
Career Center | Dallas, Texas USA | Engineering
Skills/Requirements: 5+ years in complex electronic sub-assemblies and of SMT assembly practices. Strong in DFM, DFT, ECO, BOM. Kn owledge of CAD (schematic capture, layout) PC, and Unix. People skills. Duties/Functions: Provide technical support
Career Center | Hawthorne, California USA | Engineering
SMT PROCESS ENGINEER (STARLINK) Hawthorne, CA, United States SpaceX was founded under the belief that a future where humanity is out exploring the stars is fundamentally more exciting than one where we are not. Today SpaceX is actively developing
Career Center | Wesley Chapel, Florida USA | Engineering,Management,Quality Control
15 years of experience on Electronic Manufacturing. Certified SMT Process Engineer TQM Knowledge Statistics DOE Screen Printer Thermal Process Knowledge JIT International Project Engineering Experience
Career Center | brampton, Ontario Canada | Engineering,Management,Production,Technical Support
- More than 14 years of experience in set-up, calibrate, program, troubleshoot SMT machines and SMT process, for the manufacturing of PCB Electronic Assemblies - 5 year experience in leading position for electronic manufacturing/Process Engineering.
SMT Express, Issue No. 3 - from SMTnet.com Volume 1, Issue No. 3 Wednesday, August 18, 1999 Proof Of Design a column by The MoonMan Installment One:DFM/CE - What's It All About Anyway? Continued from Front Page Make no mistake
Design & DFMA (3rd Edition) Authors: JC Blankenhorn
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/brand/support/media-relations
Media Relations Guidelines Nordson Brand Management NASDAQ $221.63 -2.40 Home Brand Overview What is the Nordson brand? Philosophy, Goals & Values Nordson Brand Promise Brand Architecture Master brand and sub-brands Trademarks
PCB Libraries, Inc. | https://www.pcblibraries.com/Forum/new-library-guidelines_topic673_post2313.html
New Library guidelines - PCB Libraries Forum Forum Home > General > General Discussion New Posts FAQ Search Events Register Login New Library guidelines
.gif)
