Quality precision die bonding / pick and place tools, collets, ejector pins, wire clamps
Suppliers Of Microelectronics & PCB Assembly Equipment & Materials, including die bond, wire bond & test & SMT screen printers & pick and place systems.
New Equipment | Curing Equipment
A Pressure Cure Oven (PCO), or Autoclave, is used to minimize voiding and increase adhesion strength for bonding processes typically used in die attach and underfill applications. PCO pressurizes air into a rigid vessel and heats & cools with
High accuracy inspection guarantees reliable defect detection of die bonds, ball-to-wedge, wedge-to-wedge and security bonds Inspection of minimal wire thicknesses up to 15 µm Reliable differentiation of wire courses Recognition of defective bon
Electronics Forum | Tue Jun 04 19:33:16 EDT 2002 | rob_thomas
Dave's estimation is pretty conservative but there is a lot of equipment out there and a lot of people happy to make a sale.Implementing both mentioned processes it's difficult and time consuming .Even if you get good training from whoever sells you
Electronics Forum | Mon May 07 22:29:52 EDT 2001 | davef
4 wire per sec ... you figure how many you need] Encapsulation ~$120K for a dispenser [10 sec per die ... you figure how many you need] plus a cure oven ~$100k Throw in a another ~$100k for marking and cleaning Check the September 2000 SMTnet New
Used SMT Equipment | X-Ray Inspection
Very Nice Nicolet Xray Machine For Sale The system is complete and in good working condition See attached pictures and information below Nicolet Imaging Systems Model Number: NXR-1500 Serial Number: 0150011 Year 2000 Variable Speed Joystick
Used SMT Equipment | General Purpose Equipment
ASM MS899-DL Wafer Mapping Die Sorter Machine is in like new condition! Serial Number: MS899DL-01817-0402 Model Number: MS899-DL Year 2008 August Cycle Time: 175 ms XY Placement: +/- 1.5 mil Die Rotation: +/- 3 degrees Collect type: Surfa
Industry News | 2003-07-02 08:54:26.0
A novel unreinforced, thermally conductive, pressure sensitive adhesive tape delivers very high bond strength to low-energy surfaces.
Industry News | 2003-04-17 08:15:33.0
In launching the LA35 series, SMAC reckons it has produced an actuator with unrivalled versatility.
Technical Library | 2014-05-08 16:34:16.0
Bare die mounting on multi-device substrates has been in use in the microelectronics industry since the 1960s. The aerospace industry’s hybrid modules and IBM’s Solid Logic Technology were early implementations that were developed in the 1960’s. The technologies progressed on a steady level until the mid 1990’s when, with the advent of BGA packaging and chip scale packages, the microelectronics industry started a wholesale move to area array packaging. This paper outlines the challenges for both traditional wire-bond die attached to a printed wiring board (pwb), to the more recent applications of bumped die attached to a high performance substrate.
Technical Library | 2014-07-24 16:26:34.0
Wire bonding a die to a package has traditionally been performed using either aluminum or gold wire. Gold wire provides the ability to use a ball and stitch process. This technique provides more control over loop height and bond placement. The drawback has been the increasing cost of the gold wire. Lower cost Al wire has been used for wedge-wedge bonds but these are not as versatile for complex package assembly. The use of copper wire for ball-stitch bonding has been proposed and recently implemented in high volume to solve the cost issues with gold. As one would expect, bonding with copper is not as forgiving as with gold mainly due to oxide growth and hardness differences. This paper will examine the common failure mechanisms that one might experience when implementing this new technology.
General curing, die attach curing, underfill curing, film & tape bonding, wafer laminating.
ACI Technologies Inc. (ACI) is a scientific research corporation dedicated to the advancement of electronics manufacturing processes and materials for The Department of Defense and industry. This video provides an overview of our commercial service
Events Calendar | Mon Apr 23 00:00:00 EDT 2018 - Thu Apr 26 00:00:00 EDT 2018 | Shanghai, China
SMTA China East Conference 2018
Events Calendar | Wed Sep 12 00:00:00 EDT 2018 - Sun Sep 30 00:00:00 EDT 2018 | ,
Improving Material Dispensing Yield in Manufacturing Applications
Career Center | Milwaukee, Wisconsin USA | Engineering
Responsible for all Wire and die bond process within this fast growing Microelectronics company. Company is constantly upgrading equipment and processes to compete in the fiber optics arena. Company will either hire fulltime or a contract worker who
Career Center | Greenville, South Carolina USA | Engineering
Process engineer with flip chip and die bonding experience is needed for a well-established company in South Carolina. This is a new position. Relocation is available. BS is required. Send resume as a Word attachment to sfrederick@connectipro.com.
Career Center | SanPedro, Philippines | Maintenance,Production
Set-up Equipment machine and ensure its proper operation for costumer satisfaction. Carry out all Proactive Maintenance (PM) tasks such as predictive maintenance, preventative maintenance, failure finding maintenance and calibration maintenan
Career Center | ORLANDO, Florida USA | Engineering,Maintenance,Production,Technical Support
Manufacturing tech/eng for a contract manufacture for 10+ years. Been working in the SMT industry for a total of 20yrs. Have done everything from operator to process work. Most familiar with Assembleon, MPM, DEK, BTU,Electrovert, SLIM-KIC, SUPER-MOLE
SMTnet Express, May 8, 2014, Subscribers: 22716, Members: Companies: 13872, Users: 36158 Challenges in Bare Die Mounting Larry Gilg, Die Products Consortium Bare die mounting on multi-device substrates has been in use in the microelectronics
| https://www.eptac.com/faqs/ask-helena-leo/ask/gold-wire-bond-failing-pull-test
) at die. (a-4) Failure in bond (interface between wire and metallization) at substrate, package post, or other than die. (a-5) Lifted metallization from die. (a-6
1st Place Machinery Inc. | http://www.firstplacemachinery.com/firstplace_asm_MS899.html
: MS899-DL Year 2008 August Cycle Time: 175 ms XY Placement: +/- 1.5 mil Die Rotation: +/- 3 degrees Collect type: Surface pick type Pick/Bond Force: 40 - 250 g (adjustable
winsouce.jpg)
.gif)
.gif)
