2,0 Cpk @ ±17,5 μmDemision:1300mm×1000mm×1600mmProduct description: ASM DEK TQ SMT Stencil Printer, Max PCB: 400x400 mm, Core cycle time：5 secs, Demision:1300mm×1000mm×1600mm, Wet print capability > 2,0 Cpk @ ±17,5 μm ASM DEK TQ SMT Stencil Prin
BGA component types, characteristics, eutectic and non-eutectic solder, ceramics, determination of profiles, equipment, BGA removal, site preparation, reballing, soldering , cleaning etc.
Electronics Forum | Wed Apr 21 21:50:28 EDT 2004 | adam
Hi I recently having problems on the components having non wetting on the flex circuits. The profile that I am using is according to the solder paste suppiler recommended. Can anyone pls. advise? Regards
Electronics Forum | Wed Sep 15 20:59:23 EDT 2010 | genesan
hi All, Here i snap shot previous PCB(HASL) and current PCB(Immersion Silver).Base on the photo it could be PCB oxidize cause the non wetting?
.JPG)
Used SMT Equipment | SPI / Solder Paste Inspection
The LSM300 follows the successful Laser section Microscopes LSM and LSM2. This new non-contact laser based system is an off-Line solder paste inspection system.LSM300 provides automatic height measurements, eliminating the inconsistencies of manual m
Industry News | 2013-07-22 09:54:27.0
GPD Global has introduced its new NCM5000 dispense pump for easy jetting. With only two wetted parts and no seals or springs to replace or adjust, field operation is simple.
Industry News | 2018-10-18 08:21:10.0
How to Prevent Non-Wetting Defect during the SMT Reflow Process
Technical Library | 2024-06-23 22:03:59.0
The melting temperatures of most lead-free solder alloys are somewhat higher than that of eutectic Sn/Pb solder, and many of the alloys tend to wet typical contact pads less readily. This tends to narrow down the fluxing and mass reflow process windows for assembly onto typical organic substrates and may enhance requirements on placement accuracy. Flip chip assembly here poses some unique challenges. The small dimensions provide for particular sensitivities to wetting and solder joint collapse, and underfilling does not reduce the demands on the intermetallic bond strength. Rather, the need to underfill lead to additional concerns in terms of underfill process control and reliability. Relatively little can here be learned from work on regular SMT components, BGAs or CSPs.
Technical Library | 2014-10-02 20:10:07.0
Sn3.0Ag0.5Cu (SAC305) is the most popular near eutectic lead-free alloy used in the manufacturing processes. Over the last several years, the price of silver has dramatically increased driving a desire for lower silver alloy alternatives. As the results, there is a significant increase in the number of alternative low/no silver lead-free solder alloys available in the industry recently.In this paper, we'll present the performance and process capability of various low/no silver alloy solder pastes. Data from printability, wetting test, slump test, solder ball test, voiding, etc… will be discussed and compared with the control SAC305 solder paste. Benefits and concerns of using low/no silver alloy solder paste materials will also be addressed.
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board
DescriptionThe Electrovert® Electra™ is an advanced, meticulously engineered wave soldering system designed for high-mass and high-volume manufacturers. Although intended for maximum throughput requirements, the Electra also offers maximum process fl
Training Courses | | | PCB Assembly Courses
The PCB assembly courses provide knowledge of different processes and equipment used in TH and SMT assembly of printed circuit boards.
Career Center | Javalera, Gen. Trias, Cavite Philippines | Engineering
Numonyx is a semiconductor company making flash memories, which was founded on March 31, 2008 by Intel Corporation, STMicroelectronics and Francisco Partners. The company supplies non-volatile memory for a variety of consumer and industrial devices i
Career Center | Rochester, New York USA | Engineering
I have done my undergraduate studies in Mechanical Engineering. I am pursuing my Master's Program in Electronics Packaging. I am currently working as a Research Assistant for RIT-CEMA (Center for Electronics Manufacturing and Assembly). My research
Career Center | Phoenix, Arizona | Engineering,Management,Production,Quality Control,Research and Development,Sales/Marketing,Technical Support
• Highly motivated, solution oriented professional with proven record synergizing scientific, engineering, and business administration backgrounds to drive and sustain customer satisfaction and long term improvements. • Articulate communicator that a
GPD Global | https://www.gpd-global.com/co_website/fluid-dispense-adhesive-application.php
Conductive Adhesive & Non-Conductive Adhesive Dispensing Home Products Fluid Dispensing Equipment High Precision Dispenser -MAX Series Large Format Board Dispensing -DS Series Table Top Dispensing Equipment Loader
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/07/leadfree.pdf
, °C ALLOY COMPOSITION, wt% PROPRIETARY AND CONFIDENTIAL INFORMATION Pages: 4 of 24 Rev Level: 1 Rev Date: 1/03/01 Eutectic Vs. Lead Free Process window comparison Conclusions
