Industry Directory | Manufacturer
Nihon has been a leader in soldering and brazing since 1966. Nihon manufactures SMT solder joining materials e.g. lead-free solder (SN100C:Sn-Cu-Ni-Ge etc): solder paste, solder spheres, flux cored solder wire, solder bar, etc.
New Equipment | Rework & Repair Equipment
BEST HotDots™ are designed to simply and cleanly attach jumper wires on a board. HotDots™ are built to survive at high temperature as both the adhesive and the polyimide material are designed to withstand wash and reflow temperatures. HotDots™ are a
New Equipment | Board Handling - Pallets,Carriers,Fixtures
* Provides dimensionally stable support platform for PCB * Protects SMT components from heat or thermal shock * Reduce/eliminate manual labor for hand masking operation, glue dotting, and hand soldering * Reduce solder defects (ex. Bridges and skips)
Electronics Forum | Fri Oct 20 14:13:32 EDT 2000 | DENNIS XIONG
Dear all, We have a PCB design mistake that causes exposed copper layers on the edges of breakaway locations. Although we fixed the design, but we already made a lot of boards plus many made before we found the problem. I wonder if any one have some
Electronics Forum | Sat Oct 21 03:55:14 EDT 2000 | DL
Dennis, I've seen this before, and in our case we didn't need to seal the edges because there was no concern of shorting or anything in the end product, this is a choice you will have to make, Does your end product have any protrusions or mounting h
Industry News | 2003-06-10 08:16:44.0
The following text describes the application of NWA Quality Analyst to quality control in the assembly of electronic components.
Industry News | 2014-10-01 15:59:00.0
PCB provider Cirtech Electronics located in Cape Town, South Africa will be liquidating their assets utilizing the online auction services of GoIndustry and Baja Bid. Bidding for the auction will open promptly at 8:00am PDT on October 7th, 2014 and will begin closing at 6:00am PDT on October 14th, 2014.
Parts & Supplies | Repair/Rework
Repair parts include: CPU circuit board repair and maintenance of the I / O board, servo circuit board repair, the image processing circuit board repair, industrial CCD camera repair, frequency converter repair, PLC repair, touch screen repair, laser
Technical Library | 2010-01-13 12:34:10.0
Micro-sectioning (sometimes referred to as cross-sectioning)is a technique, used to characterize materials or to perform a failure mode analysis, for exposing an internal section of a PCB or package. Destructive in nature, cross-sectioning requires encapsulation of the specimen in order to provide support, stability, and protection. Failures that can be investigated through micro-sectional analysis include component defects, thermo-mechanical failures, processing failures related to solder reflow, opens or shorts, voiding and raw material evaluations.
Technical Library | 2021-11-03 16:52:47.0
This paper proposes the integration of pulsed photonic sintering into multi-material additive manufacturing processes in order to produce multifunctional components that would be nearly impossible to produce any other way. Pulsed photonic curing uses high power Xenon flash lamps to thermally fuse printed nanomaterials such as conductive metal inks. To determine the feasibility of the proposed integration, three different polymer additive manufacturing materials were exposed to typical flash curing conditions using a Novacentrix Pulseforge 3300 system. FTIR analysis revealed virtually no change in the polymer substrates, thus indicating that the curing energy did not damage the polymer. Next, copper traces were printed on the same substrate, dried, and photonically cured to establish the feasibility of thermally fusing copper metal on the polymer additive manufacturing substrates. Although drying defects were observed, electrical resistivity values ranging from 0.081 to 0.103 Ω/sq. indicated that high temperature and easily oxidized metals can be successfully printed and cured on several commonly used polymer additive manufacturing materials. These results indicate that pulsed photonic curing holds tremendous promise as an enabling technology for next generation multimaterial additive manufacturing processes.
A Sustainable Alternative - Humitector cards are halogen-free and cobalt dichloride free. Visit https://www.clariant.com/solutions/products/2017/10/31/00/12/humitector-type-2-nonreversible-humidity-indicator-card?utm_source=CLRYouTube&utm_medium=Vi
Electrovert's DwellFlex 4.0 is the first solder nozzle designed specifically with Industry 4.0 automation in mind. The patent pending design enables the length of the wave to be adjusted on-the-fly as variable board types are run through the wave.
Training Courses | | | Other Courses
Other courses related to electronics manufacturing and assembly
Events Calendar | Mon Apr 23 00:00:00 EDT 2018 - Thu Apr 26 00:00:00 EDT 2018 | Shanghai, China
SMTA China East Conference 2018
Events Calendar | Tue Dec 04 00:00:00 EST 2018 - Tue Dec 04 00:00:00 EST 2018 | ,
Qualification and Reliability of Microvias
Career Center | Raleigh, North Carolina USA | Engineering
Title: SMT PROCESS ENGINEER Salary: 70k-80k max rate with great benefits Job Description: ESSENTIAL DUTIES & RESPONSIBILITIES To perform this job successfully, an individual must be able to perform each essential duty satisfactorily, plus w
SMTnet Express, May 27, 2021, Subscribers: 27,090, Companies: 11,365, Users: 26,673 Filling of Microvias and Through Holes by Electrolytic Copper Plating - Current Status and Future Outlook The electronics industry is further
| http://etasmt.com/cc?ID=te_news_industry,24564&url=_print
How to Prevent Non-Wetting Defect during the SMT Reflow Process-SMT Technical-Reflow oven,SMT Reflow Soldering Oven-cmsadmin Reflow oven,SMT Reflow Soldering Oven 当前位置: Home >> News
Imagineering, Inc. | https://www.pcbnet.com/blog/what-is-the-pcb-fabrication-process/
. Laser direct imaging exposes certain parts of the board to light in the shape of the PCB pattern. Any unexposed parts of the board will develop off, leaving the remaining film as an etch barrier The remaining film serves as an etch barrier that will be removed from the exposed copper to form the copper circuitry
