Industry Directory | Consultant / Service Provider / Distributor / Equipment Dealer / Broker / Auctions / Manufacturer / Manufacturer's Representative
DONGGUAN KINGSUN AUTOMATION TECHNOLOGY CO.,LTD is a company which mainly provide used and new SMT parts, provide repair SMT key parts service,new/used SMT machine trading,SMT consumables and Peripherals equipment,Clean room, ESD..
Industry Directory | Manufacturer
DONGGUAN KINGSUN AUTOMATION TECHNOLOGY CO.,LTD is a company which mainly provide used and new SMT parts, provide repair SMT key parts service,new/used SMT machine trading,SMT consumables and Peripherals equipment,Clean room, ESD..
Eliminate Body Stress with Versatile CF-8 GPD's CF-8 eliminates component body stress. Versatility is the key word for the CF-8. Simple tooling changes make short or long run production jobs quick and easy. Capabilities Meets exacting military s
Form & Cut 2-, 3-, 4-, 5-, and 7-leaded Radial Components Capable of forming loose radial components at rates up to 5,000 parts per hour with a variable speed motor. Feed components by hand or with tubes (TO-220s) Reduce setup time with quick ch
Electronics Forum | Tue Oct 09 12:04:37 EDT 2001 | Mike
Has anyone looked at setup reduction for machine feeders. We have made some gains through changing the flow of work but as lot sizes decrease the number of parts required remains the same. We remove all reels from the feeders after a job is complet
Electronics Forum | Sat Oct 20 00:34:57 EDT 2001 | kenbliss
Hi mike The solution is simple but two fold, first your process needs to be changed a bit, you need additional feeders to pre-stage the new P/N run and prestage the extra feeders for reload as certain higher volume components exhaust. The idea is t
Used SMT Equipment | SMD Placement Machines
* DOS * Flying Nozzle change * Fiducial camera * Pneumatic tape feeder * Locate Pin * Edge clamp * Z servo push plate * Entrance sub stop * Exit sub stop * Auto width adjust * Feeder float detection
Used SMT Equipment | SMT Equipment
Siemens SIPLACE 80 S25 SMT Pick & Place *** Refurbished by Siemens in 2007 *** Machine Dimensions: 64" x 110" x 68" (excluding light tower) Note: No Feeders or Feeder Carts are included in this lot. Serial: 666-12006556 Features: S/W Ve
Industry News | 2012-02-15 19:18:44.0
GPD Global announces that its PCD4H Dispense Pump yields excellent results with phosphor and non-phosphor-filled LED encapsulation as viewed on the color chart by tightly grouped results.
Industry News | 2003-06-10 08:16:44.0
The following text describes the application of NWA Quality Analyst to quality control in the assembly of electronic components.
Parts & Supplies | Pick and Place/Feeders
SANYO stick feeder GSF-R01 SANYO 5000 Stick Feeder The operation rate of the machine is improved by the ability of stick feeder to operate continuously over an extended period. Unlike traditional stick feeders that rapidly vibrate u
Parts & Supplies | Pick and Place/Feeders
YAMAHA Feeder Storage Cart The feeder storage cart gives your operators a secure place to put unused feeders between set-ups minimizing failures due to improper storage or handling. When its time to change over to the next job, the cart is moved t
Technical Library | 2015-04-29 03:29:56.0
Statistical Appearance Modelling technology enables an AOI system to “learn real world variation” based on operator interaction with inspection task results. This provides an accurate statistical description of normal variation in a product. With modelling technology, the user does not have to anticipate potential defects as the system will “flag” anything outside the “normal production range”. And, since the system is programmed with real production variation, it is sensitive to small subtle changes enabling reliable defect detection. Autonomous prediction of process variation enables an AOI system to be set up from a single PCB with production-ready performance. Setup time can be
Technical Library | 2013-03-27 23:43:40.0
Vapor phase, once cast to the annals’ of history is making a comeback. Why? Reflow technology is well developed and has served the industry for many years, it is simple and it is consistent. All points are true – when dealing with the centre section of the bell curve. Today’s PCB manufacturers are faced with many designs which no longer fall into that polite category but rather test the process engineering groups with heavier and larger panels, large ground planes located in tricky places, component mass densities which are poorly distributed, ever changing Pb Free alloys and higher process temperatures. All the time the costs for the panels increase, availability of “process trial” boards diminishes and yields are expected to be extremely high with zero scrap rates. The final process in the assembly line has the capacity to secure all the value of the assembly or destroy it. If a panel is poorly soldered due to poor Oven setup or incorrect programming of the profile the recovery of the panel is at best expensive, at worst a loss. For these challenges people are turning to Vapor Phase.
Eliminate Body Stress with Versatile CF-8 GPD's CF-8 eliminates component body stress. Versatility is the key word for the CF-8. Simple tooling changes make short or long run production jobs quick and easy. Capabilities Meets exacting military s
Events Calendar | Wed Mar 07 00:00:00 EST 2018 - Wed Mar 07 00:00:00 EST 2018 | ,
Solder Paste Qualification Testing - SMTA Webinar
Events Calendar | Wed Nov 28 00:00:00 EST 2018 - Wed Nov 28 00:00:00 EST 2018 | Frankfurt, Germany
Immediate Industry 4.0 Transition For Your Existing Factory, While Combatting Material Supply Issues
Career Center | Phoenix, Arizona USA | Production
More Info: https://sites.google.com/triadelectronic.com/careers-at-triad-electronic/home/surface-mount-operator Compensation: $16 to $22 Hourly Employment Type: Full-Time Why Work Here? “Family atmosphere, room for advanceme
Career Center | Fremont, California USA | Production,Quality Control
Local industry leading EMS Company seeking SMT operators. Will be doing SMT line Change overs, SMT machine operation for solder printing, placement, reflow. Solder paste height measurement and record. Solder printing quality check after solder paste
Career Center | seoul, South Korea | Engineering
I have 4 year process engineering in Motorola and 7 years service experience in Assemblen . 2 years in Mirtec AOI as service manager .
Career Center | Fredericksburg, Virginia USA | Engineering,Maintenance,Management,Production,Quality Control
• Certified CP643 Loader Calibration – FUJI American Chicago, IL 2001. • Certified - Cookson Performance Solutions BTU - PARAGON - P150 Oven – Maintenance & Electrical Troubleshooting Charlotte, NC 2001. • Certified UNIVERSAL (GSM) Platform: Operat
PCB Libraries, Inc. | https://www.pcblibraries.com/Forum/setup-preferences-menu-graphics_topic164_post3959.html
Setup > Preferences Menu Graphics? - PCB Libraries Forum Forum Home > PCB Footprint Expert > Questions & Answers New Posts FAQ Search Events Register Login Setup > Preferences Menu Graphics
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/efd/blog/072618-a-closer-look-setup-wizard-for-vision-guided-fluid-dispensing-robots
A Closer Look: Setup Wizard for Vision-Guided Fluid Dispensing Robots Nordson EFD Corporate | Global Directory | Languages Division Only All of Nordson Home Products Accessories
