Sensirion is the technology leader for intelligent sensor systems (CMOSens Technology) for digital relative humidity sensors, mass flow, gas flow and liquid flow sensors as well as differential pressure sensors. Complete OEM solutions available.
Unique Instruments for pressure, flow, level, speed, temperature, data recording. Also Gas analysis O2, CO, NO, NO2, SO2, tachometers, stroboscopes, ultrasonic
Heller 2043 MK7 SMT Reflow Oven Heating Zones: Top 13 / Bottom 13PCB Width: 50 - 560 mmWeight: 3400 kgDimension: W7224 x D1520 x H1440 mmProduct description: Heller 2043 MK7 SMT Reflow Oven, Heating Zones: Top 13 / Bottom 13, PCB Width: 50 - 560 mm,
New Equipment | Rework & Repair Equipment
NEW! Nitrogen Capable for High Yield Lead Free BGA Rework. NEW! Movable top and bottom gas heaters allows for easy rework near the edge and hard to ger area's of large PCB's. For high volume BGA Rework on even the largest computer and networking b
Electronics Forum | Wed Jun 18 01:47:25 EDT 2008 | sleech
Innovative Drying Co., considered this possibility early in our experiments. The rate of chamber pump-down is not a consideration. However, the selection of the vacuum pump is critical. Avoid oil-sealed pumps at all costs. A poorly maintained oil-tra
Electronics Forum | Thu Feb 16 02:03:36 EST 2017 | soldertraining
Reflow ovens and wave solder machines come in a huge variety of flavors and price points. These machines tell the story of impressive features and capabilities such as flux management, gas flow management, static pressure control, active cooling zone
Used SMT Equipment | Soldering - Reflow
Hello and thank you for your interest in our Heller 1088EXL Reflow Oven. See attached pictures and information Heller Reflow Oven Model Number: 1088EXL Serial Number: 0201DA1A1-53956 Year: Feb 2001 Left to Right Process Flow 8 heating zone for
Used SMT Equipment | Soldering - Reflow
Heating zones: 5 Cooling zones: 2 Total heating length: 66 in. Total cooling length: 26 in. Total process length: 127 in. Total on /off load length: 11 in. Overall system length: 138.5 in. Overall system width: 52 in. Overall system height: 5
Industry News | 2019-12-09 14:44:26.0
The SMT Reflow Soldering Equipment (Global) award was awarded to Heller Industries by Frost & Sullivan.
Industry News | 2018-01-15 13:37:11.0
The SMTA is pleased to announce the Best Papers from SMTA International 2017. As speakers at SMTA International, individuals make contributions to the industry by sharing their research and findings. For these exceptional achievements, a cash award and plaque are given to all winners.
Parts & Supplies | Assembly Accessories
SAMSUNG CP45NEO SERVO MOTOR MSMA5AZA4A J3108036A SAMSUNG CP45NEO MONITOR CABLE (KVMS) J9080360A SAMSUNG CP45NEO 45mmNEO STAGE CAMERA ASSY J9059172B SAMSUNG CP45NEO WINDOW FRONT J9052241A SAMSUNG CP45NEO GAS SPRING HS22B-330-15 J6719051A SAM
Parts & Supplies | Assembly Accessories
SAMSUNG CP45NEO SERVO MOTOR MSMA5AZA4A J3108036A SAMSUNG CP45NEO MONITOR CABLE (KVMS) J9080360A SAMSUNG CP45NEO 45mmNEO STAGE CAMERA ASSY J9059172B SAMSUNG CP45NEO WINDOW FRONT J9052241A SAMSUNG CP45NEO GAS SPRING HS22B-330-15 J6719051A SAM
Technical Library | 2019-07-10 23:36:14.0
Pockets of gas, or voids, trapped in the solder interface between discrete power management devices and circuit assemblies are, unfortunately, excellent insulators, or barriers to thermal conductivity. This resistance to heat flow reduces the electrical efficiency of these devices, reducing battery life and expected functional life time of electronic assemblies. There is also a corresponding increase in current density (as the area for current conduction is reduced) that generates additional heat, further leading to performance degradation.
Technical Library | 2015-03-26 19:16:03.0
Nickel-palladium-gold-finished terminals are susceptible to creep corrosion. Excessive creep corrosion can result in device failure due to insulation resistance loss between adjacent terminals. The mixed flowing gas test has been demonstrated to produce creep corrosion on parts with nickel-palladium-gold finished terminals. Conformal coats are often used to protect printed wiring assemblies from failure due to moisture and corrosion. However, coating may not be sufficient to protect lead terminations from failure.In this study, acrylic, silicone, urethane, parylene, and atomic layer deposit (ALD) coatings were examined for their effectiveness at preventing corrosion of nickel-palladium-gold-finished terminals.
· What is the difference between SMT vacuum reflow soldering machine and ordinary reflow soldering machine? · What problems can be solved by smt vacuum reflow soldering machine? · What is the basic principle of vacuum reflow machine? · Ho
The biggest, baddest, most affordable Nitrogen Capable BGA Rework Station demonstrated by Dennis O'Donnell the BGA Expert! Safe, precision rework for SMD, BGA, and LED chips on boards as large as 36" or more!. The versatile E6250U rework station co
Events Calendar | Tue Feb 18 00:00:00 EST 2020 - Tue Feb 18 00:00:00 EST 2020 | ,
Corrosion Testing For Electronic Equipment
Career Center | Corpus Christ, Texas USA | Engineering,Quality Control
This position reports to the Quality Manager and provides support in all areas of fabrication and assembly of passive components exceeding customer requirements and expectations in a fast paced environment. Support is defined as but not limited to th
Career Center | Colton, California USA | Engineering,Maintenance,Production,Quality Control,Research and Development,Technical Support
• Strong experience with the installation, training, and repair on a variety of electro-mechanical, pneumatic, PLC, or computer controlled systems. • Strong Knowledge in SMT equipment, Screen Printer, AOI/SPI, Conformal Coat Systems, Reflow oven, X-R
Career Center | Moline, USA | Management,Production,Technical Support
Numerous years experience developing complete manufacturing processes for electronic assemblies.
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/07/ultralow.pdf
. For a given gas mass flow and velocity exiting the openings of the oven, the lower the flow turbulence, the lower the probability of air and oxygen flowing upstream and into the oven
winsouce.jpg)
