Industry Directory | Equipment Dealer / Broker / Auctions / Manufacturer / Manufacturer's Representative / Training Provider
Global OEM manufacturer of selective wave soldering machines. With a world-wide install base in over 65 countries, we are a global leader in the selective soldering space. Highly customized solutions available in all industries.
Industry Directory | Consultant / Service Provider / Manufacturer
Flux is your source for custom cable assembly, wire harness, and electrical enclosure manufacturing. We design and manufacture to your specification and can assist with connector selection, layout, and manufacturing techniques.
New Equipment | Rework & Repair Equipment
The new inspection mirror meets clean room requirements yet is sufficiently economical for non-clean room applications. A quality tool for the technician but inexpensive enough to meet the budgetary requirement of modern manufacturing. Economical Br
New Equipment | Cleaning Equipment
Features: 1. A comprehensive cleaning system: the surface of the product residues of organic matter, inorganic substances for thorough and effective cleaning; 2. Automatic cleaning mode: in a clean room to complete the cleaning, rinsing, drying all
Electronics Forum | Mon Aug 30 15:43:22 EDT 2004 | ryufoong
i will try on it. Thanks a lots. Regards, CHEN
Electronics Forum | Sat Aug 28 19:31:36 EDT 2004 | ryufoong
Currently, in my working factory, we facing the flux residue remain on connector after washing. (of course, this is clean process with WS solder paste). So, are there any ways to clean the flux residue rather than go back to wash again? Because wash
Used SMT Equipment | Pick and Place/Feeders
FUJI SMT machine AIMEX IIIC-Flexible High-Mix Production Freeing up more floor space with its compact design and reduced lengthThis is an all-in-on machine with scalability and the ultimate level of versatility necessary for increasing productivity f
Used SMT Equipment | Pick and Place/Feeders
FUJI SMT machine AIMEX IIIC-Flexible High-Mix Production Freeing up more floor space with its compact design and reduced lengthThis is an all-in-on machine with scalability and the ultimate level of versatility necessary for increasing productivity f
Industry News | 2012-05-11 20:35:45.0
Heller Industries has been awarded a 2012 SMT VISION Award in the category of Soldering Reflow for its 1936 Mark 5 Reflow Oven. The award was presented on April 25, 2012 at the Nepcon China Exhibition.
Industry News | 2003-06-05 08:11:23.0
Kerry co-solvent system pays for itself in 13 months
Parts & Supplies | Pick and Place/Feeders
The definition of SMT SMT is the surface assembly technology,surface mount technology(surface mount technology)(Surface Mounted Technology abbreviation),is currently the most popular electronic assembly industry,a technology and technology. What a
Parts & Supplies | Pick and Place/Feeders
SMT basic process components include: silk screen (or dispensing), placement (curing), reflow soldering, cleaning, testing, repair 1, silk screen: its role is to paste or patch solder paste printed on the PCB pad, the components f
Technical Library | 2020-03-09 10:50:17.0
A customer called the Helpline seeking advice for cleaning no-clean fluxes prior to applying a conformal coating. The customer's assemblies were manufactured with a no-clean rosin based solder paste (ROL0) and were cleaned with an isopropyl alcohol (IPA) wash. After cleaning, a white residue was sometimes found in areas with high paste concentrations and was interfering with the adhesion of the conformal coating (Figure 1). For conformal coatings to adhere properly, the printed circuit board (PCB) surface must be clean of fluxes and other residues. In addition, ionic contamination left by flux residues can lead to corrosion and dendrite growth, two common causes of electronic opens and shorts. Other residues can lead to unwanted impedance and physical interference with moving parts.
Technical Library | 2019-06-03 15:32:40.0
ACI Technologies was pleased to assist a customer by conducting elemental analysis on several assemblies displaying severe corrosion. Several board assemblies had failed in the field and exhibited areas of corrosion in close proximity to onboard components. The most common source of corrosion on electronic assemblies is residual flux. Fluxes are specific chemistries applied during the soldering process which improve the wetting of the solder to both the pad and component when forming the solder joint. They can be highly reactive chemicals that, if left on the assemblies, can lead to corrosion, electrical degradation, and decreased reliability. In the presence of moisture and electrical bias, flux residue can enable dendritic growth as a result of electrochemical migration (ECM).
Flux spray coating on a PCB with uniformal thickness down to 5 microns, with clear edge definition and minimal overspray. Can coat large or shoot dots with the same jet.
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Training Courses | ONLINE | | PCB Assembly Courses
The PCB assembly courses provide knowledge of different processes and equipment used in TH and SMT assembly of printed circuit boards.
Events Calendar | Tue Apr 14 00:00:00 EDT 2020 - Tue Apr 14 00:00:00 EDT 2020 | ,
Why Are We Cleaning No-Clean?
Events Calendar | Mon May 10 00:00:00 EDT 2021 - Mon May 10 00:00:00 EDT 2021 | ,
Europe Chapter Webinar: Manual Cleaning of Printed Board Assemblies – Step by Step Guide
Career Center | Riyadh 11623, Philippines | Engineering,Maintenance,Production
PROFESSIONAL EXPERIENCE: Connected in the field of manufacturing/electronics industry experienced in the line, Through Hole and Surface Mount Technology, worked on various Fuji Machines Universal model, such as: CP 643E chip shooter QP 242E chip mou
Career Center | , Minnesota USA | Engineering,Management,Production,Quality Control,Technical Support
Engineer with a diverse background in management, quality, computer and customer service. Experience includes optics, electrical, mechanical, physics, chemistry, process and systems engineering, implementing computers and computer applications for m
Article Return to Front Page No-Residue Technolo
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/select/technologies-or-options/microdrop-flux-dispenser
mitigated by solder nozzle without flux residue or ionic contamination - Compact design allows for easy servicing providing a maintenance-free production environment with minimal machine downtime - Available on Novo ®
| https://www.eptac.com/webinar/flux-classification-part-2-selecting-the-right-flux-for-your-application/
. This Webinar will provide you with a brief insight into: The Purpose of Flux Impact of Flux Residue Selection and Qualification Process Flux Performance Specifications Course Length: 44 Minutes Cost: FREE Presenter(s
