Industry Directory | Manufacturer
Manufacture defluxers, cleaners & maintenance solutions used to remove solder paste, flux residues, SMT Adhesives and other soils during the manufacture of electronic components or during the assembly of printed circuit boards.
Industry Directory | Manufacturer
Aoki Laboratories Ltd. is an ISO-9002 certified company specializes in manufacturing of Sn/Pb Bar Solder, Cored Wire and Paste.Environmental friendly products, such as: lead-free solder, no-clean non-halide solder flux, no-clean cored wire and Non-CFC cleaner, are compliance with ISO-14001 requirements.
New Equipment | Rework & Repair Equipment
The new inspection mirror meets clean room requirements yet is sufficiently economical for non-clean room applications. A quality tool for the technician but inexpensive enough to meet the budgetary requirement of modern manufacturing. Economical Br
Flux application using the DispenseJet® pump is a superior alternative to screen printing and ultrasonic spray. Jet dispensing eliminates the overspray and material waste associated with ultrasonic and spray application methods. Flux application usi
Electronics Forum | Tue Dec 11 10:12:36 EST 2007 | George
Hi everybody, Is there any criteria as far as No-clean flux residues surrounding solder joints when using selective solder machines? I have a Novastar SPA 400 and use flux NC kester 959. If I decrease the amount of flux, then I experience problems w
Electronics Forum | Thu Dec 13 08:02:02 EST 2007 | realchunks
You may want to try raising your pre-heater if you have one. I would also suggest trying different fluxes that may be a little more active so you can use less. What type of fluxer are you using? Selective solder flux residue is a gray area. This i
Used SMT Equipment | Board Cleaners
Aqueous Tech Trident 111 Must sell posted 5/5/15 208V 3 phase 40 Amps Year 2008 Trident III is capable of removing all flux residues including rosin, no-clean and water soluble. Both lead and lead-free flux residues may be removed using the
Used SMT Equipment | Soldering - Reflow
BTU Pyramax 125N Parameters Pyramax Specifications Model Pyramax 125N Atmosphere Air or Nitrogen Conveyor Speed 10-60 in/min 25-152 cm/min Conveyor Width 2-18 in 51-457 mm Heated Length 125 in 3175 mm Heated Zones&
Industry News | 2012-05-11 20:35:45.0
Heller Industries has been awarded a 2012 SMT VISION Award in the category of Soldering Reflow for its 1936 Mark 5 Reflow Oven. The award was presented on April 25, 2012 at the Nepcon China Exhibition.
Industry News | 2003-06-05 08:11:23.0
Kerry co-solvent system pays for itself in 13 months
Technical Library | 2018-08-29 21:17:53.0
No-clean solder pastes are widely used in a number of applications that are exposed to wide variations in temperature during the life of the assembled electronics device. Some have observed that cracks can and do form in flux residue and have postulated that this is the result of or exacerbated by temperature cycling. Furthermore, the potential exists for the flux residue to soften or liquefy at elevated temperatures, and even flow if orientated parallel to gravity. In situations such as in automotive electronics, where significant temperature cycling is a reality and high reliability is a must, concern sometimes exists that the cracking and possible softening or liquefying of the residue may have a deleterious effect on the electrical reliability of the flux residue. This paper will attempt to address this concern.
Technical Library | 2018-11-20 21:33:57.0
There are several industry-accepted methods for determining the reliability of flux residues after assembly. The recommended methods of test sample preparation do not always closely mimic the thermal cycle experienced by an assembly. Therefore, extraction from actual assemblies has become a popular method of process control to assess consistency of post-reflow cleanliness. Every method of post-reflow flux residue characterization will depend on the reflow process followed to prepare the coupon.This investigation will focus on the effect of thermal conditions on the remainder of active ingredients in flux residues after assembly with no-clean solder pastes.
Flux spray coating on a PCB with uniformal thickness down to 5 microns, with clear edge definition and minimal overspray. Can coat large or shoot dots with the same jet.
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Training Courses | ONLINE | | PCB Assembly Courses
The PCB assembly courses provide knowledge of different processes and equipment used in TH and SMT assembly of printed circuit boards.
Events Calendar | Mon Jun 08 00:00:00 EDT 2020 - Mon Jun 08 00:00:00 EDT 2020 | ,
Practical Set-Up, Qualification of Cleaning Process in PCB Assembly
Events Calendar | Tue Apr 14 00:00:00 EDT 2020 - Tue Apr 14 00:00:00 EDT 2020 | ,
Why Are We Cleaning No-Clean?
Article Return to Front Page No-Residue Technolo
SMTnet Express, December 29, 2016, Subscribers: 30,326, Companies: 15,062, Users: 41,660 Partially-Activated Flux Residue Impacts on Electronic Assembly Reliabilities Yanrong Shi, Ph.D., Kyle Loomis, Jennifer Allen, Bruno Tolla, Ph.D.; Kester
| https://www.eptac.com/soldertips/issues-of-burnt-flux-on-class-3-pcb-assemblies/
: Flux residues are flux residues, regardless of whether it is burnt or not. Reference section 10.6.1 Cleanliness – Flux Residues in the 610
Precision PCB Services, Inc | https://precision-pcb-services-inc.com/products/amtech-nws-4400-ha-tf-water-washable-lead-free-tacky-solder-flux-rem1
: As a rule of thumb removing M1/H1 flux residues is paramount, however it is an easy task – use warm de-ionized water at 40-60°C with recommended water pressure of 30-50 PSI – NWS
