Industry Directory | Manufacturer / Manufacturer's Representative
We specialize in EMI Ferrite Core, Thermal Pads, Gaskets and shielding products.
Industry Directory | Consultant / Service Provider
CAD Design Software products run in the AutoCAD environment.
New Equipment | Rework & Repair Services
BGA Rework Services Offered BGA Remove and Placement Level Three Pad Repair Wire Add Trace Repair BGA Re-Balling BGA Inspection We Rework PBGA (Plastic Ball Grid Array) TBGA (Tape Ball Grid Array) uBGA (Micro BGA) CCGA (Ceramic Colum
Used for Coaxial measurements. The probes are 50 ohm impedance and the ground shield extends to test pad. Patented Design
Electronics Forum | Fri Oct 16 14:11:16 EDT 2009 | davef
thermal and pad
Electronics Forum | Thu Oct 15 11:04:28 EDT 2009 | spitkis2
Thanks Jim. Pressing the QFN into paste was what I thought of, just wasn't sure if it would cause solder paste to be pressed outside the pad area and possibly bridge with an adjacent pad. Do you recall the ratio of paste coverage to the pad area?
Used SMT Equipment | Repair/Rework
SPLIT VISION MICROSCOPE STEREO WILD M3Z MICROSCOPE WITH ZOOM LENS COLOR DIGITAL CAMERA CAMERA MONITOR REMOTE KEY PAD CONTROLLER AIR/NITRO INLET INCLUDES 3 EACH NOZZLES FOOT SWITCH FOR GAS FLOW TOP AND BOTTOM 800 WATT HEATERS VENTURE VACUUM SYSTEM GRO
Used SMT Equipment | General Purpose Equipment
Blue M Mechanical Convection Oven, 96 cu.ft., F4 Control Product includes the following installed options: Computer Interface: RS485 Standard with Controller Door Style: Standard Double Door Door Hinge: Standard Special ETO Option : Install leve
Industry News | 2019-03-03 18:51:58.0
The SMTA Capital Chapter and UP Media Group/Circuits Assembly Magazine are pleased to co-sponsor this Chapter Tutorial Program on March 28 featuring presentations by Yaad Eliya and Jim Barry of PCB Technologies.
Parts & Supplies | Assembly Accessories
amaha Mounter: also known as "mounting machine" and "surface mounting system", in the production line, it is a kind of equipment that can accurately place surface mount components on PCB pad by moving the mounting head after dispe
.JPG)
Parts & Supplies | Pick and Place/Feeders
J44021035A PC_POWER_SUPPLY J48011017A SBC NuPRO-935A/DV &n
Technical Library | 2018-09-26 20:33:26.0
Bottom terminated components, or BTCs, have been rapidly incorporated into PCB designs because of their low cost, small footprint and overall reliability. The combination of leadless terminations with underside ground/thermal pads have presented a multitude of challenges to PCB assemblers, including tilting, poor solder fillet formation, difficult inspection and – most notably – center pad voiding. Voids in large SMT solder joints can be difficult to predict and control due to the variety of input variables that can influence their formation. Solder paste chemistries, PCB final finishes, and reflow profiles and atmospheres have all been scrutinized, and their effects well documented. Additionally, many of the published center pad voiding studies have focused on optimizing center pad footprint and stencil aperture designs. This study focuses on I/O pad stencil modifications rather than center pad modifications. It shows a no-cost, easily implemented I/O design guideline that can be deployed to consistently and repeatedly reduce void formation on BTC-style packages.
Technical Library | 2019-04-11 06:04:49.0
With the development of science and technology, the climatic chamber quality has been improved, and the failure rate is reduced, but there still have the failure probability.today we introduce what are the mian factors for big noise high low temperature test chamber: 1.External factors: the bottom angle is uneven, the ground is uneven, adjust the bottom angle, ensure the equipment is in a horizontal position; 2.The equipment is touched other objects or pushed against the wall,pls remove the objects and keep a certain distance from the wall. 3.Compressor noise:check whether the compressor collides with the pipeline,and evaporator dish is loose or not. 4.Check whether compressor shock absorbers are aging and replace them. 5.Solenoid valve noise: solenoid valve reversing caue loud sound, pls add damping glue, if no effect, need to replace solenoid valve. If there is AC noise, need to replace the power board. 6.Check wether the fan or the fan string shaft make noise,whether the fan blades are touched and deformed, whether the fan is fixed or not, pls adjust accordingly or add the rubber pad. If further technical questions,contact us without hesitation!---Climtest Symor® technical team
we have many hitachi equipment and hitachi feeders to sell . if you want to know more , please contact us tina@smtfeeders.cn
we have many hitachi equipment and hitachi feeders to sell . if you want to know more , please contact us tina@smtfeeders.cn
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/dage/test-types/first-bond-ball-pull-stud-bump-pull?con=t&page=16
. First bond ball pull utilises cold bump pull jaw technology to apply a vertical load (a pull test) to ball bonds and stud bumps. Ball shear tests can sometimes promote pad cratering due to the aggressive nature of the bonding process which can weaken the ball bonds
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/FLOware-Messages-Reference-Guide-22100026.pdf
. Click DONE to st ABORT to stop th Attach Ground Clip to Needle Click CONTINUE When Done This message appears during calibration before touch down of a dispense needle on a machine with an electrical touch pad
