Industry Directory | Distributor / Manufacturer / Manufacturer's Representative
European supplier of Lead Free solder products like the paste compositions SnZnAl (low melting point), SAC, SnBi, flux, BGA Balls, solder wire, N2 Reflow Systems.
Industry Directory | Manufacturer
Suppliers of solder pastes, wave soldering liquid fluxes and SMT adhesives and cored solder wires for all soldering requirements.
New Equipment | Solder Materials
5N Plus produces indium in pure metal, chemical and low melting point alloy forms for use in electronics, solar cells and optics. Indium is essential in forming transparent electrodes from indium tin oxide (ITO) in liquid crystal displays (LCD) and t
New Equipment | Solder Materials
KappAloy9™ - 91%Sn - 9%Zn - 390°F (199°C) eutectic alloy is the best solder for soldering Aluminum wire to Copper busses or soldering Copper wire to Aluminum busses or contacts. Its low eutectic melting point minimizes heating of critical electrical/
Electronics Forum | Thu Oct 21 05:42:15 EDT 2010 | jacki
Dear All Does anyone know about the low melting point solder paste which should be Copper Base? Usually the Copper base solder has 227'C of melting point.
Electronics Forum | Mon Nov 01 04:40:29 EDT 2010 | jacki
Hi Mark thanks and useful. However, I couldn't find the Copper base solder paste which melting point is lower than 210'C.
Industry News | 2003-06-24 08:14:51.0
R/flex� 3850 laminate is produced in a range of copper and LCP thicknesses, just as the single-clad laminate, and is available in standard panel formats.
Industry News | 2018-04-17 21:06:54.0
SMTA is excited to announce the technical program has been finalized and registration is now open for the International Conference for Electronics Enabling Technologies. The event will be held June 5-7, 2018 in Markham, Ontario, Canada.
Technical Library | 2022-10-31 17:25:37.0
Mixed formulation solder alloys refer to specific combinations of Sn-37Pb and SAC305 (96.5Sn–3.0Ag–0.5Cu). They present a solution for the interim period before Pb-free electronic assemblies are universally accepted. In this work, the surfaces of mixed formulation solder alloys have been studied by in situ and real-time Auger electron spectroscopy as a function of temperature as the alloys are raised above the melting point. With increasing temperature, there is a growing fraction of low-level, bulk contaminants that segregate to the alloy surfaces. In particular, the amount of surface C is nearly _50–60 at. % C at the melting point. The segregating impurities inhibit solderability by providing a blocking layer to reaction between the alloy and substrate. A similar phenomenon has been observed over a wide range of (SAC and non-SAC) alloys synthesized by a variety of techniques. That solder alloy surfaces at melting have a radically different composition from the bulk uncovers a key variable that helps to explain the wide variability in contact angles reported in previous studies of wetting and adhesion. VC 2011 American Vacuum Society. [DOI: 10.1116/1.3584821]
Technical Library | 2013-01-24 19:16:35.0
The electronics industry has mainly adopted the higher melting point Sn3Ag0.5Cu solder alloys for lead-free reflow soldering applications. For applications where temperature sensitive components and boards are used this has created a need to develop low melting point lead-free alloy solder pastes. Tin-bismuth and tin-bismuth-silver containing alloys were used to address the temperature issue with development done on Sn58Bi, Sn57.6Bi0.4Ag, Sn57Bi1Ag lead-free solder alloy pastes. Investigations included paste printing studies, reflow and wetting analysis on different substrates and board surface finishes and head-in-pillow paste performance in addition to paste-in-hole reflow tests. Voiding was also investigated on tin-bismuth and tin-bismuth-silver versus Sn3Ag0.5Cu soldered QFN/MLF/BTC components. Mechanical bond strength testing was also done comparing Sn58Bi, Sn37Pb and Sn3Ag0.5Cu soldered components. The results of the work are reported.
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board
· What is the difference between SMT vacuum reflow soldering machine and ordinary reflow soldering machine? · What problems can be solved by smt vacuum reflow soldering machine? · What is the basic principle of vacuum reflow machine? · Ho
Events Calendar | Thu Oct 21 00:00:00 EDT 2021 - Thu Oct 21 00:00:00 EDT 2021 | ,
Great Lakes Chapter Webinar: Low Melting Alloy & Selection of the Right Chemistry for Reliability
Events Calendar | Mon Apr 23 00:00:00 EDT 2018 - Thu Apr 26 00:00:00 EDT 2018 | Shanghai, China
SMTA China East Conference 2018
SMTnet Express, July 1, 2015, Subscribers: 22,969, Members: Companies: 14,445, Users: 38,464 Reliability Screening of Lower Melting Point Pb-Free Alloys Containing Bi Joseph M. Juarez, Michael Robinson, Joel Heebink; Honeywell International
SMT Express, Issue No. 5 - from SMTnet.com Volume 1, Issue No. 5 Wednesday, October 13, 1999 Featured Article Return to Front Page HASL WHAT A HASSLE, or HASL'd AGAINby Earl Moon INTRODUCTION This article updates one I wrote for Printed
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/07/leadfree.pdf
– Joints Look Ugly but are fine • Bismuth – Reduces melting point but joints can be brittle depending on formulation • Antimony – – Gives better stability at low temperatures when used with tin
| https://www.eptac.com/do-you-know-all-of-the-applications-for-soldering/
. Without this convenient, low-melting point alloy, modern electronics wouldn’t be able to function or even exist. Metalwork Soldering can also be used in metal working and is used to make and repair jewelry and musical instruments