Industry Directory | Other / Manufacturer
TTi makes standard and custom thermal platforms, Hybrid Benchtop Temperature Chambers which combine the benefits of a small benchtop chamber with a separately controlled thermal platform for speed, uniformity versatility.
New Equipment | Rework & Repair Equipment
BEST HeatShield Gel™ is a thermal shield water-based gel designed to be used in the PCB rework/repair or board assembly areas in order to provide thermal protection of electronic components. It is truly a revolutionary means to protect components. It
New Equipment | Cleaning Equipment
I.C.T-5200 | SMT Fixture Cleaning Machine Equipment Introduction: I.C.T-5200 Fixture Cleaning Machine is used to clean grease, flux, dusts on the surface of all kinds of SMT fixtures，tray, reflow oven cooler and filter, wave-soldering oven claw,
Used SMT Equipment | Stencil Cleaners
SmartSonic Ultrasonic Stencil Wash • Model: 529 • Year: 2018 • Enviroguard-P Filtration System • Hand-Held Spray Rinse • Hand-Held Air Blow-Off • Footprint: 21.8" x 35.5" x 31"H • Wash Tank Dim
Used SMT Equipment | Board Cleaners
Trident ZDO, Single Chamber Flux Remover Vintage 3/5/2020 Deinstalled and located in MI Serial number 9930 Removes All Flux Types, Closed-Loop (Zero Discharge) Wash Cycle, Closed-Loop (Zero Discharge) Rinse Cycle Automatic Wash, Rinse & and Dry Cycle
Industry News | 2003-06-05 08:11:23.0
Kerry co-solvent system pays for itself in 13 months
Industry News | 2016-01-05 16:10:10.0
Novel method for protecting electronic components from heat.
.jpg)
Technical Library | 2020-12-10 15:49:40.0
Electronic assemblies should have longer and longer service life. Today there are partially demanded 20 years of functional capability for electronics for automotive application. On the other hand, smaller components, such as resistors of size 0201, are able to endure an increasing number of thermal cycles until fail of solder joints, so these are tested sometimes up to 4000 cycles. But testing until the end of life is essential for the determination of failure rates and the prognosis of reliability. Such tests require a lot of time, but this is often not available in developing of new modules. A further acceleration by higher cycle temperatures is usually not possible, because the materials are already operated at the upper limit of the load. However, the duration can be shortened by the use of liquids for passive tests, which allow faster temperature changes and shorter dwell times because of better heat transfer compared to air. The question is whether such tests lead to comparable results and what failure mechanisms are becoming effective. The same goes for active temperature cycles, in which the components itself are heated from inside and the substrate remains comparatively cold. This paper describes the various accelerated temperature cycling tests, compares and evaluates the related degradation of solder joints.
Technical Library | 2018-11-20 21:33:57.0
There are several industry-accepted methods for determining the reliability of flux residues after assembly. The recommended methods of test sample preparation do not always closely mimic the thermal cycle experienced by an assembly. Therefore, extraction from actual assemblies has become a popular method of process control to assess consistency of post-reflow cleanliness. Every method of post-reflow flux residue characterization will depend on the reflow process followed to prepare the coupon.This investigation will focus on the effect of thermal conditions on the remainder of active ingredients in flux residues after assembly with no-clean solder pastes.
Squeegee Cleaning Machine ETA-4200 If you could not find any similar items you want, you may send some photos to us. because our catalog and website haven't included all of our products. PCBA Cleaning Machine, On-line PCBA Cleaning Machine, Ste
Events Calendar | Mon Sep 29 18:30:00 UTC 2025 - Tue Sep 30 18:30:00 UTC 2025 | San Diego, California USA
YINCAE Showcases High-Performance Materials at IMAPS 2025
Career Center | Davenport, Iowa USA | Production
SURFACE MOUNT SOLDERER - COOLERS Cobham Mission Systems is seeking a Surface Mount Solderer for our Coolers Department within our Davenport, Iowa facility. This position is open due to an increase in staff. The qualified applicant will perform the
Career Center | Tewksbury, Massachusetts USA | Engineering
Mycronic is a global high-tech company whose innovative solutions have been advancing electronics technology for over 40 years. Today we continue to grow and serve customers in an expanding variety of industries. What we do impacts the future of tech
Career Center | Lindenhurst, Ajman | Engineering
� Entrepreneurial and management skills, efficient in computer tools, worked in ISO9000 environment; adept to product certification process in hi-tech industry. Supervised at times up to 40 engineers and other professionals. Tolerates ambiguity and p
Career Center | Rochester, New York USA | Engineering,Production,Sales/Marketing,Technical Support
Working Experience: Fairchild Semiconductor, South Portland, ME Package Simulation Co-op: Technology CAD Group (Mar.2002-Present) Thermal simulation for 40 lead fine pitch QSOP & 48 lead one die fine pitch QSOP: Created a 3D model
Lewis & Clark | http://www.lewis-clark.com/shop/
: MyReflow 7038 Vintage: 2006 Details: 8 Heated Zones 2 Cooling Zones Edge Rail 350° Max Temp Condition: Complete & Operational Shipping
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/adhesive-dispensing-systems/industries/electronics-assembly-and-packaging?page=2
Electronics manufacturing, particularly mobile consumer devices, is seeing shorter product life cycles requiring more flexible production processes
winsouce.jpg)