Industry Directory | Manufacturer
US manufacturer of metallized ceramic substrates & packages; specializing in PCTF (plated copper over thick film) & low cost AgENIG (silver with electroless nickel and immersion gold plating).
High Tech, Quick Turn, Manufacturer of PCB's up to 44 layer count. Specializing in Prototype and R&D. Mil-Spec 31032 & 55110 Certified. Located in Fremont, CA & Amesbury, MA.
New Equipment | Education/Training
This is a "real life" how to solder kit including both throughhole and SMT components. The board has ground planes that you would find in a real PCB assembly. Upon completion the sudents will have a working board. If you are trying to instruct new
Ridgid, bare board manufacturing of military, high reliability, quick-turn, prototype, single, double-sided, and multilayer boards, blind and buried vias, carbon ink, immersion silver, immersion tin, reflow, hasl, nickel and gold, all colors of legen
Electronics Forum | Tue Sep 23 10:06:29 EDT 2008 | Sean
Hello Vlad, Davef, Your valuable inputs are much appreciated. Many thanks, Sean.
Electronics Forum | Sat Sep 20 07:11:28 EDT 2008 | Sean
Hello All, I used to hear that PCB with immersion silver finishing, its non component location pads, tend to be discolour (Yellowish) after went through heat cycle, such as reflow oven. However, if the component solderbility on the PCB is OK, can w
Industry News | 2003-05-19 10:06:43.0
The PCB is available with a maximum panel size of 406-by-460mm and a minimum board thickness of 0.8mm.
Industry News | 2003-02-07 09:13:12.0
The Sessions Covered Current and Emerging Technologies
Parts & Supplies | Circuit Board Assembly Products
1). 1+C+1 HDI, buried/blind L1-L5/L5-L8 vias. 2). FR-4 Material, 1 oz weight. 3). 8 layer, 1.6mm thick. 4). 4/4 mils track and space 5). Min.drill 0.1mm 6). Green solder mask/ white silkscreen 7). Immersion gold over nickel
Parts & Supplies | General Purpose Equipment
The conductive elastomer have good conductive,and the products are mainly used in army electronic equipments like spaceflight,aviation,ect. We can produce this products according the drawing supplied by our customers. The materials: Silicon with Si
Technical Library | 2015-11-25 14:15:12.0
In this study various printed circuit board surface finishes were evaluated, including: organic solderability preservative (OSP), plasma finish (PF), immersion silver (IAg), electroless nickel / immersion silver (ENIS), electroless nickel / immersion gold hi-phosphorus (ENIG Hi-P), and electroless nickel / electroless palladium / immersion gold (ENEPIG). To verify the performance of PF as a post-treatment option, it was added to IAg, ENIG Hi-P, and ENEPIG to compare with non-treated. A total of nine groups of PCB were evaluated. Each group contains 30 boards, with the exception on ENIS where only 8 boards were available.
Technical Library | 2018-05-09 22:15:29.0
Creep corrosion on printed circuit boards (PCBs) is the corrosion of copper metallization and the spreading of the copper corrosion products across the PCB surfaces to the extent that they may electrically short circuit neighboring features on the PCB. The iNEMI technical subcommittee on creep corrosion has developed a flowers-of-sulfur (FOS) based test that is sufficiently well developed for consideration as an industry standard qualification test for creep corrosion. This paper will address the important question of how relative humidity affects creep corrosion. A creep corrosion tendency that is inversely proportional to relative humidity may allow data center administrators to eliminate creep corrosion simply by controlling the relative humidity in the data center,thus, avoiding the high cost of gas-phase filtration of gaseous contamination. The creep corrosion relative humidity dependence will be studied using a modified version of the iNEMI FOS test chamber. The design modification allows the achievement of relative humidity as low as 15% in the presence of the chlorine-releasing bleach aqueous solution. The paper will report on the dependence of creep corrosion on humidity in the 15 to 80% relative humidity range by testing ENIG (gold on electroless nickel), ImAg (immersion silver) and OSP (organic surface preservative) finished PCBs, soldered with organic acid flux.
This is what the fully assembled How to Solder Kit looks like. Depress the button and one of the LEDs will remain lit at the end (it eventually times out). You can add some kind of template so each LED position has some meaning. The PCB has a real gr
Events Calendar | Wed Apr 20 00:00:00 EDT 2022 - Wed Apr 20 00:00:00 EDT 2022 | ,
Virtual Course: Selection Criteria of Surface Finish for Next Generation PCB Technologies
Career Center | Phoenix, Arizona | Engineering,Management,Production,Quality Control,Research and Development,Sales/Marketing,Technical Support
• Highly motivated, solution oriented professional with proven record synergizing scientific, engineering, and business administration backgrounds to drive and sustain customer satisfaction and long term improvements. • Articulate communicator that a
Imagineering, Inc. | https://www.pcbnet.com/capabilities/assembly/technology-roadmap/
• Inner Layer - 10 oz • Inner Layer - 16 oz Buried/Blind Via 10+N+10 (HDI) Plasma Desmear Yes Outline Tolerance +/-.004 Surface Finish • HASL • ENIG • Immersion Silver • OSP (ENTEK) • Carbon • Immersion Tin • Electrolyic Gold • ENEPIG • ENIPIG Impeadance Control
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/ipc-standards-for-manufacturing-assembly_topic877_post9030.html
and Flexible Adhesive Bonding Films IPC-4204 - Flexible Metal-Clad Dielectrics for Use in Fabrication of Flexible Printed Circuitry IPC-4552 - Specification for Eletroless Nickel/Immersion Gold (ENIG
winsouce.jpg)
