About Us Our company is based on the belief that our customers' needs are of the utmost importance. Our entire team is committed to meeting those needs. As a result, a high percentage of our business is from repeat customers and referrals. We woul
Electronics Forum | Fri Aug 17 09:35:15 EDT 2007 | karenp
We usually do Solder reworks, and some components that cannot be installed by SMT Machines or Wave solder due to specs or the technology in our company... aur work methods and instruction are always based on designators and are more illustrated to ca
Electronics Forum | Mon Nov 26 22:05:34 EST 2007 | shy
currently i'm open my stencil aperture is 80% from the land pattern. is this will cause insufficient solder at the terminal component or not? the stencil thichness is 6mil and the board run using SMT pallet which i consider there will be no option f
Industry News | 2017-10-05 12:40:41.0
The new whitepaper highlights the specific benefits of bentonite clay in terms of composition, moisture-adsorption performance, production requirements, and the environmental impact of available moisture controlled packaging solutions.
Industry News | 2020-04-18 14:12:00.0
IPC yesterday sent a letter to U.S. President Donald Trump, Mexican President Andrés Manuel López Obrador and Canadian Prime Minister Justin Trudeau, urging them to launch a trilateral initiative to mobilize industrial base support for the continuing medical response related to COVID-19.
Technical Library | 2013-12-05 17:09:03.0
The functionality of electronic devices continues to increase at an extraordinary rate. Simultaneously consumers are expecting even more and in ever smaller packages. One enabler for shrinking electronics has been the flexible circuit board that allows the circuit board to fit a wide variety of shapes. Flexible printed circuits (FPC) have the capability to be very thin and can have unpackaged components directly attached using surface mount technology (SMT) and flip chip on flex technologies. Bare die can also be thinned and attached very close to the circuit board. However one caveat of high density flexible circuit boards with thin die is that they can be very fragile. The use of back side films and underfill can protect the die making circuits more robust. For underfill to work well it requires good adhesion to the circuit board which can mean that flux residues under the die normally must be removed prior to underfilling.
Technical Library | 2021-03-18 20:07:08.0
X-ray tomography is a promising technique that can provide micron level, internal structure, and three dimensional (3D) information of an integrated circuit (IC) component without the need for serial sectioning or decapsulation. This is especially useful for counterfeit IC detection as demonstrated by recent work. Although the components remain physically intact during tomography, the effect of radiation on the electrical functionality is not yet fully investigated. In this paper we analyze the impact of X-ray tomography on the reliability of ICs with different fabrication technologies.
Events Calendar | Wed Aug 19 00:00:00 EDT 2020 - Wed Aug 19 00:00:00 EDT 2020 | ,
DfR - Design for Rinse-Ability: Effect of SMT Component Package Design on Cleaning Effectiveness
Events Calendar | Thu Jul 20 00:00:00 EDT 2023 - Thu Jul 20 00:00:00 EDT 2023 | Suwanee, Georgia USA
Atlanta Chapter Technical Meeting: The Science of Humidity Control in Manufacturing
Career Center | San Pablo City, Laguna, Philippines | Engineering,Maintenance,Production,Sales/Marketing,Technical Support
Some key points you may find relevant to this job opportunity include: Extensive experience and knowledge on Service and Technical skills by performing Set-up, Buy-off, troubleshooting of the assigned Equipments. Provide solution to custom
SMT Express, Volume 3, Issue No. 10 - from SMTnet.com Volume 3, Issue No. 10 Thursday, October 18, 2001 Featured Article Return to Front Page Odd or SMD? by Anton Mandos and Paul Gerits , Assembl�on b.v. Odd or SMD? At one time
SMTnet Express May 9, 2013, Subscribers: 26129, Members: Companies: 13373, Users: 34687 Impact of Dust on Printed Circuit Assembly Reliability by: Bo Song, Michael H. Azarian, Michael G. Pecht; CALCE Atmospheric dust consists of solids suspended
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/our-company/news-room/feature-content-roll-up-page/cecilia-render-snapshot
. What is one of your favorite Nordson Impact memories? I always like when I get to interact with students. But I remember one time we were on a board site tour, so it was the executive team, and we were visiting what is now one of our national programs, Tech Corp
| https://www.eptac.com/soldertips/smt-component-shifting/
SMT Component Shifting | EPTAC Skip to content Scroll Toll Free: 800.643.7822 Toggle navigation Training All Classes Standard’s Expert Training On-Site Training Customized Training Discounts Online Training Training Materials Locations All Locations East Coast Midwest West Coast South Canada Resources Ask Helena & Leo Soldertips ®
COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.
2481 Hilton Drive
Gainesville, GA USA
Phone: (770) 538-0411
