GDK Single Lane 3D Solder Paste Inspection Machine,Spi Machine Production Overview: SLE/SLE-D is used to detect and monitor the quanlity of solder paster printing. With the increasing precision of electronic products, chip components are becoming s
New Equipment | Test Equipment
Online AOI Machine S810 Inspection Component: 01005 chip PCB size::50×70mm-510×460mm Dimension:1000mm×960mm×1600mm Weight: 710kg Product description: Online AOI Machine S810, Inspection Component: 01005 chip, PCB size:
Electronics Forum | Fri Feb 24 02:04:50 EST 2017 | soldertraining
Selective Soldering Frames can pull large amounts of heat from the solder wave at the point of contact, effectively lowering the temperature of the solder at the solder joint. You should confirm the temperature of the solder joints by running a therm
Electronics Forum | Thu Jun 23 11:56:51 EDT 2005 | wjxingggg
Hi, all. There is one 0.8mmX0.8mm QFN on almost of our PWBAs. But the quality report showed that we got bad solder quality for this component. My question is which elements are the root cause for this situation frequently? Thanks.
Industry News | 2020-01-06 16:06:59.0
MIRTEC will premier its complete line of 3D AOI and SPI Inspection Systems in Booth #1900 at the 2020 IPC APEX EXPO. The premier technical conference and exhibition for the electronics manufacturing industry will take place Feb. 4-6, 2020 at the San Diego Convention Center.
Industry News | 2023-07-22 11:28:46.0
If need more technical support , pls contact with us at Jenny@ksunsmt.com
Technical Library | 2019-06-21 10:39:15.0
Recently, an ACI Technologies (ACI) customer called to discuss failures that they had observed with some through-hole capacitor parts. The components were experiencing failures following vibration and accelerated stress testing. Upon receipt of the samples, ACI performed three levels of inspection and Energy Dispersive Spectroscopy (EDS) testing to investigate the root cause of the failures. These analyses enabled ACI to verify the elements comprising the solder joints and make the following recommendations in order to prevent future occurrences. The first inspection was to investigate the capacitor leads using optical microscopy, and no anomalies were found that could indicate bad parts from the vendor or improper handling prior to assembly. However, vertical fill in the barrel of the plated through-holes was too close to the IPC-A-610 minimum specification of 75% to determine a pass/fail condition, and therefore required further investigation.
Technical Library | 2018-11-07 03:31:04.0
Generally speaking, there are not many cases of insufficient solder and solder short in BGA soldering, but it is not impossible. Here we discuss some elements may cause it
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board
Events Calendar | Wed Dec 06 00:00:00 EST 2017 - Wed Dec 13 00:00:00 EST 2017 | Rolling Meadows, Illinois USA
X-Ray of PCBs Webtorial
SMT Express, Volume 2, Issue No. 3 - from SMTnet.com Volume 2, Issue No. 3 Thursday, March 16, 2000 Featured Article Return to Front Page Curtailing Voids in Fine Pitch Ball Grid Array Solder Joints by Gary Morrison and Kevin Lyne
SMT Express, Volume 2, Issue No. 6 - from SMTnet.com Volume 2, Issue No. 6 Wednesday, June 14, 2000 Featured Article Return to Front Page Process Control for Solder Flux Stacy KaliszMark OwenMVTechnology Ltd. ABSTRACT Flux used in ball grid
Imagineering, Inc. | https://www.pcbnet.com/blog/identifying-and-correcting-solder-bridge-defects/
. Unfortunately, there are numerous causes that can produce solder bridging. To produce as quickly and efficiently as possible, finding the root cause of this defect is critical
| https://www.eptac.com/blog/5-common-solder-mistakes-and-how-to-resolve-them
. 4. Cold Solder Joint A cold solder joint occurs when the solder does not melt completely. A result of insufficient heat, cold joints are often characterized by being rigid, rough, and uneven in appearance
