Industry Directory | Consultant / Service Provider / Manufacturer
BBG will service your quick turn prototype, your small volume run as well as your full production requirement. We have plants dedicated to quick turn, small volume and prototype applications.
Industry Directory | Manufacturer
Supplier of High-Tech Low-Cost Printed Circuit Boards with 1-48 layers from 24h express. Flex, flex-rigid, metal core, impedance control, blind & buried vias as well as SMD Stencils.
New Equipment | Board Handling - Conveyors
Model No: KSUN 250 Automatic un Loader PCB loading time: Approx 6seconds Magazine change-over time: Approx 30 seconds Power supply: 100-230V AC (customized ), single phase, MAX 300V/A Air pressure: 4-6 bar, MAX 10L/minute Transport height: 900±
New Equipment | Board Handling - Conveyors
product instruction ※PLC control system, Working is stably and reliably ※Easy to operate touch screen control interface ※the pneumatic clamps of top and bottom three point provided for the magazine alignment ※Electric pushing board design ca
Electronics Forum | Fri Oct 03 05:27:24 EDT 2003 | kanwal324
the puspose of solder mask is to prevent exposure of cu tracks to atmosphere. the lesser thickness can effect the performance of board but it only depends on its application. if you are making telecom board then its not good to use the board.
Electronics Forum | Wed Jan 25 18:31:05 EST 2012 | kahrpr
A few years ago a lot of stencils were 6 mill and 7 mills and a lot of people still use them. these days with such a hi mix on the boards 5 mill seems to be a good compromise. if the 6 mills is working for you that's fine. One thing to note as you go
Used SMT Equipment | Chipshooters / Chip Mounters
FUJI, Chip Shooter, type CP643E, s.n. 2066, Left to right, cap. 40.000 CPH, Device input 140-8mm, with 20 heades, 6 nozels each, 2 tables 70 feeders each, PCB dimensions Max: 457mm x 356mm Min: 80mm x 60mm,Board Thickness: 0.3 to 4.0 mm, Component ca
Used SMT Equipment | Chipshooters / Chip Mounters
FUJI, Chip Shooter, type CP643E, s.n. 1278, Left to right, cap. 40.000 CPH, Device input 140-8mm, with 20 heades, 6 nozels each, 2 tables 70 feeders each, PCB dimensions Max: 457mm x 356mm Min: 80mm x 60mm,Board Thickness: 0.3 to 4.0 mm, Component ca
Industry News | 2017-08-19 13:31:56.0
GPD Global will demonstrate its Hyperion dispense system in booths 1C03 & 1C10 at upcoming NEPCON South China 2017. This fully automated dispense platform incorporates the latest technology from GPD Global in a compact footprint. Equipped with linear motor drives, smart pump technology, full touch screen interface, vision centric system operation & more, this is a dispense system not to be missed.
Industry News | 2003-05-19 10:06:43.0
The PCB is available with a maximum panel size of 406-by-460mm and a minimum board thickness of 0.8mm.
Parts & Supplies | Circuit Board Assembly Products
1). PCB Thickness up to 5mm 2). FR-4 material, 1 oz copper finished 3). Green solder mask /white silk screen. 4). Blind/buried vias required. 5). Hot air level Pb free 6). Application: motor, medical equipment, industrial products.
Parts & Supplies | Circuit Board Assembly Products
1) Rogers4350B/4003C, Double-sided Layer, 2) 0.5mm thick/0.2mm thick 3) 1/1 oz copper thickness 4) Line space width: 0.15-0.2mm 5) Immersion gold.
Technical Library | 2015-07-21 13:50:37.0
Achieving an even coat at the right desired thickness is a major challenge when it comes to applying conformal coating to a Printed Circuit Board (PCB). Applying a coating too thin will ultimately render the electronic assembly vulnerable to potential environmental risks therefore defeating the purpose of the coating. Apply the coat too thick, and it could leave the electronic specific components non-functional therefore destroying the electronic assembly entirely. Coating thickness must meet quality specifications. Measurements for coating thickness may be taken while film is dry or wet. Once measurements are recorded, thickness is compared to quality specifications and fluid dispensing automation machinery is calibrated as necessary. There are a handful of methods for measuring conformal coating thickness that are commonly used in the Electronic Manufacturing Services (EMS) and Original Electronic Manufacturer (OEM) industries. A few commonly used methods for checking conformal coating thickness include:
Technical Library | 2013-10-13 10:54:13.0
The measurement of the conformal coating thickness on a printed circuit board (PCB) to ensure internal and international standards are met is now a critical factor in conformal coating process control. There are several methods for measurement of conformal coating thickness and they fall into two categories. These categories are wet film measurements applied during coating application and dry film measurements made after the coating is dried enough not to damage the coating.
http://www.gpd-global.com Tilt-and-Rotate configuration is available. Full featured programming makes conformal coating processes quick and easy. 3-axis Conformal Coating System for printed circuit boards that provides a reliable robotic platform f
Hot Sale pcb Push-up stacker for chip mounter Assembly Line Product introduction: 1.This equipment is used to collect bare PCBs at the end of SMT production line 2.Stable and reliable PLC control system; 3.Easy to operate LED touch screen control
Training Courses | | | IPC-6012 Specialist (CIS)
The Certified IPC-6012 Specialist (CIS) training covers design, fabrication and inspection of rigid printed boards.
Training Courses | | | IPC-600 Specialist (CIS)
The Certified IPC-600 Specialist (CIS) training targets quality assurance and acceptance of bare printed circuit boards.
Events Calendar | Mon Sep 14 00:00:00 EDT 2020 - Mon Sep 14 00:00:00 EDT 2020 | ,
Printed Circuit Board (PCB) Inspection & Quality Control
Events Calendar | Wed Jul 03 00:00:00 EDT 2024 - Wed Jul 03 00:00:00 EDT 2024 | ,
Europe Chapter Webinar: "Back-to-Basics" SMT Assembly
Career Center | Shen Zhen, China | Management,Sales/Marketing
Working in GLORYPCB for 10 years.knowing electronic supply chain very well. especially for PCB PCBA assembly and other Electronic Manufacturing Service.Glorypcb is a professional electronic manufacturer located in Shenzhen with three facilities.offe
Career Center | Erode, Tamilnadu India | Engineering
Professional Summary 3+ years of experience in the PCB CAM engineering Exposure to FRONTLINE GENESIS 2000 Having exposure in UCAM Exposure to Create, Array & Panelize it for manufacturability Experienced in Creating impedance cou
Influence of Pd Thickness on Micro Void Formation of Solder Joints in ENEPIG Surface Finish SMTnet Express December 13, 2012, Subscribers: 26067, Members: Companies: 9068, Users: 34058 Influence of Pd Thickness on Micro Void Formation of Solder
KD Electronics Ltd. | http://www.kundasmt.com/?A-Equipment-Accessories/6009.html
-02 Incremental encoder MS101 Y-axis/S/F-D 03047223-02 WPC controller board 03047225-02 WPC power supply board 03047255-01 Barcode/WPC 03047270-01 Circular level 03047273-02 Bero Reference-point feed
