Industry Directory | Consultant / Service Provider / Manufacturer / Other
Fully automated assembly, advanced product introduction processes. ISO quality system compliance, high standards for medical, military, and other discerning markets. Quick turn prototyping, lower cost per engagement inc. low volume prod.
Yamaichi Electronics is an international manufacturer of Memory Card connectors, test & burn-in-sockets, production sockets, test contactors, and high-density connectors.
New Equipment | Selective Soldering
The Model WDS-900 is a top-of-the-line Nitrogen Capable BGA Rework System with a High-Resolution Split Vision Optical System for Removal, Placement, and Soldering of BGAs, CGA's, CSPs, QFPs, LGA's and Other SMDs. An excellent BGA Rework Machine or f
New Equipment | Rework & Repair Equipment
The Model WDS-900 is a top-of-the-line Nitrogen Capable BGA Rework System with a High-Resolution Split Vision Optical System for Removal, Placement, and Soldering of BGAs, CGA's, CSPs, QFPs, LGA's and Other SMDs. An excellent BGA Rework Machine or f
Electronics Forum | Sat Aug 07 09:32:54 EDT 2010 | scotceltic
We have a Large LGA package (40mm X 40mm) that we are trying to process on a double-sided assembly. problem is the only space we have for it is on 1st side processing side. Therefore we have worries about falling off in the oven during the 2nd side
Electronics Forum | Wed Apr 13 10:05:58 EDT 2016 | donnie15
I am working on soldering an Large LGA module to a PCB and am having some issues with opens due to variation in the board flatness. I have tried adding more paste but get shorts and excess flux as I get above a 7 mil stencil. I have tried adding sol
Industry News | 2013-02-05 14:13:33.0
BGA Rework System Demo Tour
Industry News | 2021-05-21 03:56:59.0
LED lamp bead because of energy saving, low carbon environmental protection, no strobe, no radiation, high brightness, low heat advantages are gradually replacing the fluorescent lamp on the market, its application scope is expanding,although LED has many advantages, if the production or operation is not appropriate,there will be LED strip use fault phenomenon. LED lamp strip manufacturers also begin to pay more and more attention to the problem of production quality, then what equipment can be used for LED lamp strip backlight detection? Unicomp Technology here recommended AX8200L LED strip backlight detection equipment.
Parts & Supplies | Repair/Rework
Three independent heaters control systems. FG-P6000 is available heating portion of the PCB board by hot-air circulate both from top and bottom at the same time. With large IR bottom heating, it can completely avoid PCB deformation during reworking
Technical Library | 2016-10-03 08:28:47.0
With the miniaturization of electronic device, Land Grid Array (LGA) or QFN has been widely used in consumer electronic products. However there is only 20-30 microns gap left between LGA and the substrate, it is very difficult for capillary underfill to flow into the large LGA component at room temperature. Insufficient underfilling will lead to the loss of quality control and the poor reliability issue. In order to resolve these issues, a room temperature fast flow reworkable underfill has been successfully developed with excellent flowability. The underfill can flow into 20 microns gap and complete the flow of 15mm distance for about 30 seconds at room temperature. The curing behavior, storage, thermal cycling performance and reworkability will be discussed in details in this paper.
Technical Library | 2017-08-17 12:28:30.0
At SMT assembly, flux outgassing/drying is difficult for devices with poor venting channel, and resulted in insufficiently dried/burnt-off flux residue for no-clean process. Examples including: Large low stand-off components such as QFN, LGA Components covered under electromagnetic shield which has either no or few venting holes Components assembled within cavity of board Any other devices with small open space around solder joints
The biggest, baddest, most affordable Nitrogen Capable BGA Rework Station demonstrated by Dennis O'Donnell the BGA Expert! Safe, precision rework for SMD, BGA, and LED chips on boards as large as 36" or more!. The versatile E6250U rework station co
BGA component installation demo with the Shuttle Star SV560 that has the Side View Camera option.
Events Calendar | Mon Dec 02 00:00:00 EST 2019 - Mon Dec 02 00:00:00 EST 2019 | ,
Webinar: QFN/LGA Design, Assembly Process Issues & Reliability Failures
Career Center | Wesley Chapel, Florida USA | Engineering,Management,Quality Control
15 years of experience on Electronic Manufacturing. Certified SMT Process Engineer TQM Knowledge Statistics DOE Screen Printer Thermal Process Knowledge JIT International Project Engineering Experience
Precision PCB Services, Inc | https://precision-pcb-services-inc.com/collections/bga-rework-stations/products/model-rw-sv2000a-bga-rework-station
. 1 year part warranty. Lifetime technical support. Suitable for large Servo, Base station, Industrial computer repair, able to rework difficult components like CGA 、 BGA 、 QFN 、 CSP 、 LGA 、 Micro SMD 、 MLF(Micro Lead Frames
Heller Industries Inc. | https://hellerindustries.com/smt-reflow-ovens/smt-reflow-oven/
SMT Reflow Oven -MK5 SMT Reflow Oven Home » SMT Reflow Oven For Large PCB Reflow Soldering » SMT Reflow Oven -MK5 SMT Reflow Oven SMT Reflow Oven -1913 MK5 Best value SMT Reflow Oven in the market
