Industry Directory | Manufacturer / Other
TWC manufactures custom Cable/wire harness for specific applications based upon customer design and print requirements. •Wire Leads, Battery Cables, Tinning and Soldering, Cable/Wire Harnesses, Power Cords, Ribbon Cable Assembly
Middle Size Lead Free SMT Reflow Oven for LED A600 Model: A600 MID-sized Lead-free Reflow Oven(6-zone) Brief: Lead-free reflow soldering Heating System > Eight groups of top and bottom forced hot air convection heating zones. > Patented heati
LED reflow oven for 3W high power LED E10 Main product: Reflow oven with 10 zones, hot air reflow oven, SMT equipment, PCB Assembly Equipment, PCB Assembly Equipment, SMD/SMT Assembly, SMT assembly line, automatic production line Heating System &
Electronics Forum | Thu Aug 22 23:09:34 EDT 2019 | sssamw
Yes, you need work with supplier to see if can run pin in paste for these connectors, even do some experiments. A step-up stencil would be good for these connectors, also connectors pin size and length match with PCB hole design.
Electronics Forum | Tue Dec 11 12:29:57 EST 2012 | deanm
Thanks for the comments so far. The smallest nozzle I've tried is a 4mm, which is what Pillarhouse used on this board to provide a sample. I tried this but wasn't as good as the 6mm. I've soldered the same connectors on a different board using a 10mm
Used SMT Equipment | SMT Equipment
Many Fuji Sparr parts for sales.. No Part No. Description Qty. Machine 1 GPH4580 HOLDER 7 CP43 2 MPH0472 PISTON 19 CP43 3 GPL1200 PIN 8 CP43 4 S1046A CIR-CLIP WR19 10 CP43 5 PPQ1020 PIN,LOCATING 1 CP43 6 GXT2333 HOLDER,PIN 2 CP43 7 MPA5031 COLLAR 2 C
Used SMT Equipment | In-Circuit Testers
Agilent/HP 16089C Kelvin IC Clip Lead. Purchase includes 30 Day Warranty, and 7 Day Right of Refusal The 16089C makes it possible to measure odd-shaped components that cannot be measured with conventional fixtures. It is equipped with two insulate
Industry News | 2003-03-04 08:08:23.0
In a move that broadens its interconnect design services, Micromark C and CD has introduced a new development kit for the Flexstrip jumpers flexible interconnect system.
Industry News | 2003-03-27 08:15:33.0
Modular Embedded Circuit Board from parvus Enables Local Device Fingerprint Biometrics
Parts & Supplies | Pick and Place/Feeders
DEK - SQUEEGEE DEK BOM SQA lead free ..45 degree 200mm length There are also other DEK parts for you !!!DEK MOTOR 107707 DRIVE BELT^RAIL WIDTH DEK 185938 DRIVE BELT^TABLE LIFT DEK 185934 DEK Q-250D COVERS SYSTEM SWITCH LOOM BOM DEK DEK 1635
.jpg)
Parts & Supplies | Pick and Place/Feeders
FUJI COVER for nxt3 ..2AGTGA006403 Wholesales price of smt spare parts, weclome to inquiry! Lead time: 2-4 working days There are also other FUJI spare parts for you ! WWZ0242 PLATE WWZ0271 PLATE K5049N CONNECTOR K5049L CONNECTOR H5449T BO
Technical Library | 2020-05-07 03:46:27.0
The selective soldering process has evolved to become a standard production process within the electronics assembly industry, and now accommodates a wide variety of through-hole component formats in numerous applications. Most through-hole components can be easily soldered with the selective soldering process without difficulty, however some types of challenging components require additional attention to ensure optimum quality control is maintained. Several high thermal mass components can place demands on the selective soldering process, while the use of specialized solder fixtures and/or pallets often places an additional thermal demand on the preheating process. Fine-pitch through-hole components and connectors place a different set of demands on the selective soldering process and typically require special attention to lead projection and traverse speed to minimize bridging between adjacent pins. Dual in-line memory module (DIMM) connectors, compact peripheral component interface (cPCI) connectors, coax connectors and other high thermal mass components as well as fine-pitch microconnectors,can present challenges when soldered into backplanes or multilayer printed circuit board assemblies. Adding to this challenge, compact peripheral component interface connectors can present additional solderability issues due to their beryllium copper termination pins.
Technical Library | 2022-08-08 15:06:06.0
Selective soldering has evolved to become a standard production process within the electronics assembly industry, and now accommodates a wide variety of through-hole component formats in numerous applications. Most through-hole components can be easily soldered with the selective soldering process without difficulty however some types of challenging components require additional attention to ensure that optimum quality is maintained. Several high thermal mass components can place demands on the selective soldering process, while the use of specialized solder fixtures, or solder pallets, often places additional thermal demand on the preheating process. Fine-pitch through-hole components and connectors place a different set of demands on the selective soldering process and typically require special attention to lead projection and traverse speed to minimize bridging between adjacent pins. Dual in-line memory module (DIMM) connectors, compact peripheral component interface (cPCI) connectors, coax connectors and other high thermal mass components as well as fine-pitch microconnectors, can present challenges when soldered into backplanes or multilayer printed circuit board assemblies. Adding to this challenge, compact peripheral component interface connectors can present additional solderability issues because of their beryllium copper base metal pins. Key Terms: Selective soldering, drop-jet fluxing, sustained preheating, flux migration, adjacent clearance, lead-to-hole aspect ratio, lead projection, thermal reliefs, gold embrittlement, solderability testing.
https://www.ascen.ltd/Products/Component_lead_forming_machine/ Motorized version ASCEN taped component axial lead forming machine AS-809F axial lead former, use for cut and bend axial components braid resistor,capacitor, inductor, diode and other ele
https://www.ascen.ltd/Products/Component_lead_forming_machine/ Motorized version ASCEN taped component axial lead forming machine AS-809F axial lead former, use for cut and bend axial components braid resistor,capacitor, inductor, diode and other ele
Training Courses | | | IPC/WHMA-A-620 Specialist (CIS)
The Certified IPC/WHMA-A-620 Specialist (CIS) training focuses on cable and wire harness fabrication and installation.
SMT Placement for ICs, Connectors and Odd Shaped Components SMT Placement for ICs, Connectors and Odd-Shaped Components Accurate component placement is a basic requirement for any pick and place machine. The first step towards accurate placement
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/products/fittings-and-connectors?con=t&page=3
Support Suppliers Resources Careers Home Product Type Fittings and Connectors Industrial Fittings and Connectors Trust in industrial fittings and connectors from Nordson MEDICAL for precision fluid
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/07/00600-228.pdf
. Heated length 105" [267 cm] 9-zone Air Convection Configuration (L-R) 150" [381 cm] (2) Cool zone(2) Center draw exhaust Figure 3. This reflow oven design for lead-free processing features nine zones
