Industry Directory | Manufacturer
Professional, Reliable,High Quality,Low Cost, Rapid Delivery PCB manufacturer
Industry Directory | Manufacturer
We provide cost effective, custom printed circuit boards (PCBs) through an instant online system. We also provide PCB Assemb
New Equipment | Fabrication Services
Our Service PCB Assembly and PCB&PCBA design are our main business.We are able to undertake a high quality Printed Circuit Board Assembly on competitive prices and flexible conditions.We are a complete “One- Stop” resource for printed circuit board
New Equipment | Assembly Services
Our Service PCB Assembly and PCB&PCBA design are our main business.We are able to undertake a high quality Printed Circuit Board Assembly on competitive prices and flexible conditions.We are a complete “One- Stop” resource for printed circuit board
Electronics Forum | Tue Jul 06 15:06:35 EDT 1999 | Mike Demos
Is anyone aware of some guidelines regarding through-hole in SMT pads? One of our designers wants to add through-hole leads in some SMT pads for an inductor. The size of the hole is 0.032 inches and takes-up approximately 25% of the pad area. This
Electronics Forum | Mon Feb 19 22:56:20 EST 2007 | davef
Russ We agree with your comments on plugging from one side only. But... We believe that it IS possible to trap process chemicals [technically, not flux] in a blind [or any other] via. This can be done by plating the via closed, rather than pluggi
Industry News | 2013-03-12 11:34:11.0
GPD Global has appointed Technical Resources Corporation (TRC) as its representative in Florida, Puerto Rico and the Caribbean.
Industry News | 2016-02-27 22:07:08.0
GPD Global will exhibit in Booth#1818 at the upcoming IPC APEX EXPO 2016 Conference and Exhibition. See a live demonstration of 01005 dispensing on the MAX series high precision dispenser, the intuitively programmed Island series benchtop dispenser, and a full range of dispense pumps used on GPD dispense systems.
Technical Library | 2016-11-30 15:53:15.0
The use of microvias in Printed Circuit Boards (PCBs) for military hardware is increasing as technology drives us toward smaller pitches and denser circuitry. Along with the changes in technology, the industry has changed and captive manufacturing lines are few and far between. As PCBs get more complicated, the testing we perform to verify the material was manufactured to our requirements before they are used in an assembly needs to be reviewed to ensure that it is sufficient for the technology and meets industry needs to better screen for long-term reliability. The Interconnect Stress Testing (IST) protocol currently used to identify manufacturing issues in plated through holes, blind, or buried vias are not necessarily sufficient to identify problems with microvias. There is a need to review the current IST protocol to determine if it is adequate for finding bad microvias or if there is a more reliable test that will screen out manufacturing inconsistencies. The objective of this research is to analyze a large population of PCB IST coupons to determine if there is a more effective IST test to find less reliable microvias in electrically passing PCB product and to screen for manufacturing deficiencies. The proposed IST test procedure will be supported with visual inspection of corresponding microvia cross sections and Printed Wiring Assembly (PWA) acceptance test results. The proposed screening will be shown to only slightly affect PCB yield while showing a large benefit to screening before PCBs are used in an assembly.
Welcome to this Defect of the Month video on via hole failures and how to see them, this series of videos were produced for and featured as part of the NPL/IPC video library and examples are taken from the NPL Defect Database. Over the last couple of
Training Courses | | | PCB Assembly Courses
The PCB assembly courses provide knowledge of different processes and equipment used in TH and SMT assembly of printed circuit boards.
SMTnet Express March 7, 2013, Subscribers: 26214, Members: Companies: 13311, Users: 34412 PTH Core-to-Core Interconnect Using Sintered Conductive Pastes The market for high-layer-count printed circuit boards (PCB) containing blind and buried vias
SMTnet Express, May 12, 2022, Subscribers: 25,588, Companies: 11,569, Users: 27,213 Electronics Manufacturing Technical Articles Filling of Microvias and Through Holes by Electrolytic Copper Plating –Current Status and Future
| http://www.feedersupplier.com/SMT_THROUGH_HOLE
. Initially, all electronic components were through-hole mounted. Through-hole components have metal leads, and these leads are fed through-plated holes in the circuit board
Imagineering, Inc. | https://www.pcbnet.com/blog/class-ii-vs-class-iii-inspection-standards-in-pcb-assembly/
. There is a difference between Class 2 and Class 3 when it comes to the amount of barrel fill that’s used in the through-hole leads
