Industry Directory | Manufacturer
Supplier of high quality engineered materials, including conductive and resistive inks, UV curable dielectrics and insulators, adhesives, coatings, transducer inks and potting compounds.
Industry Directory | Manufacturer
Suppliers of adhesive and dispensing solutions. Techcon dispensers, metering valves, robots, plastic components, air guns and accessories. Henkel Sicomet anaerobic and cyanoacrylate adhesives, Henkel Dexter epoxy resins and adhesives, Jenome dispensing robots. Keltech pressure pot dispensers. Packaging service for transfer of adhesives from drums, pots or cans into syringes and cartridges.
New Equipment | Rework & Repair Equipment
Poor handling procedures may sometimes damage corners and edges on printed circuit boards. Most of these types of damage to PCB's can be repaired using the BEST Board Repair Kit. This versatile repair kit along with our clear "how to" instructions of
General purpose and special inks, including MIL-STD epoxy.
Electronics Forum | Wed Jun 16 09:46:02 EDT 2004 | blnorman
Have you considered spraying the coating? Check with the manufacturer of the epoxy to see if they recommend any equipment and whether or not the coating would have to be mixed with solvent to provide a smooth, thin even coat.
Electronics Forum | Sat Aug 07 11:10:03 EDT 1999 | JohnW
| Could someone give recommendation on the stencil opening for printing epoxy on HAL FR4 PCB for 0805 and 0603 size chips capacitors and resisitors. | My regular stencil manufacturer recommend the following: | Thickness: 8 mils | 0805 opening: Oblong
Used SMT Equipment | Adhesive Dispensers
TH-2004ab T&H Two component mixer/meter dispensing system Features: 1. Have a big capacity cartridge, make the time of importing materials minimum, and reduce waste. 2. Adopted with the TH-700J pneumatic double-liquid valve can
Used SMT Equipment | Adhesive Dispensers
Standards: CE approvedLiquid ratio: 1:1-3:1 (can be adjusted) Viscosity: Mixing method: static mixer The machine has automatic mixing and automatic dispensing function. Dispensing precision is highly, speed is fast, and Position is accu
Industry News | 2017-06-14 10:46:29.0
GPD Global offers uniquely designed 2-part mixing pump to accurately mix and dispense two-part components while eliminating entrapped air.
Industry News | 2011-08-22 15:44:33.0
GPD Global will debut its Positive Cavity Displacement (PCD) 'H' Series high-resolution pumps in Booth #1849 at the upcoming Assembly & Automation Technology Expo, scheduled to take place September 20-22, 2011 at McCormick Place North in Chicago, IL.
Parts & Supplies | Assembly Accessories
Supply SMT Fuji placement machine accessories FUJI XP242 Feida interface board ADEEE6700 ADEE6700 Supply SMT placement machine accessories JUKI CB thimble L = 64.10mm Supply SMT Fuji FUJI placement machine QP electric Feida 24MM cover AKDDC6561 AKD
Technical Library | 2021-08-25 16:28:36.0
In this study, a Sn–Bi composite solder paste with thermosetting epoxy (TSEP Sn–Bi) was prepared by mixing Sn–Bi solder powder, flux, and epoxy system. The melting characteristics of the Sn–Bi solder alloy and the curing reaction of the epoxy system were measured by differential scanning calorimeter (DSC). A reflow profile was optimized based on the Sn–Bi reflow profile, and the Organic Solderability Preservative (OSP) Cu pad mounted 0603 chip resistor was chosen to reflow soldering and to prepare samples of the corresponding joint. The high temperature and humidity reliability of the solder joints at 85 #14;C/85% RH (Relative Humidity) for 1000 h and the thermal cycle reliability of the solder joints from
http://www.gpd-global.com No drip no drool across a wide range of fluid viscosities (low-to-mid and low-to-high). No manual adjustment to compensate for pump variability. Truly Volumetric PCD Pumps for total control of dispensing fluids. Ability to
PCB pad repair technique demonstrated using the 2-part epoxy method. More on this PCB pad repair technique: http://www.solder.net/services/pcb-repair/pad-and-trace-repair/ More on the recommended epoxy: http://www.soldertools.net/pcb-repair-epoxy-r
Career Center | San Jose, California | Production
Looking for an experienced sprayer of acrylics, polyurethanes, silicones & epoxies. Experience with HVLP equipment, mixing of materials (by weight & by volume). Able to follow process instructions, read Technical data sheets and apply coating to de
Career Center | Colton, California USA | Engineering,Maintenance,Production,Quality Control,Research and Development,Technical Support
• Strong experience with the installation, training, and repair on a variety of electro-mechanical, pneumatic, PLC, or computer controlled systems. • Strong Knowledge in SMT equipment, Screen Printer, AOI/SPI, Conformal Coat Systems, Reflow oven, X-R
Career Center | GARLAND, Texas USA | Production
exp in Fuji, Juki and universal smt pick and place machines . Component verification.
GPD Global | https://www.gpd-global.com/pdf/pump/Two-Part-Mixing-Pump.pdf
Volumetric Two Part Mixing Pump Disposable Static Mixer, No Recharge Volumetric Two Part Mixing Pump Precision Dispensing Systems www.gpd-global.com • request@gpd
| http://etasmt.com:9060/cc?ID=te_news_bulletin,10161&url=_print
. One is a finished board and the other is a bare board. PCB (Printed Circuit Board) is called "printed circuit board" and is made of epoxy glass resin material
.gif)
