Industry Directory | Manufacturer
Design and Manufacture Desiccant Dry Cabinets for low humidity storage and baking of moisture sensitive components, PCBs, electronic materials, lab samples, digital media and medical devices.
Industry Directory | Consultant / Service Provider / Equipment Dealer / Broker / Auctions / Manufacturer / Manufacturer's Representative
Moisture-proof Humidity&Drying Solutions Our company is specialized in manufacturing dry cabinet.drying oven.We have Dry Cabinet,Nitrogen Cabinet,Baking Cabinet,Air Blast Drying Oven and Vacuum Oven.
The MSL baking process at OX3 Corporation, (�MSL� stands for Moisture Sensitivity Level), is in accordance with IPC and JEDEC Standard "J-STD-033A," the joint industry standard for semiconductor handling, packing, shipping and the use of moisture/ref
Reflow cycle - runs the oven through the pre-defined temperature profile.> Bake cycle - used to drive the moisture from moisture-sensitive components.>
Electronics Forum | Tue Aug 19 12:15:37 EDT 2003 | D Peter
Again, that is for packaging, rather than moisture removal or storage. Those guidlines are for several reasons, preventing low pressure outgassing or disassociation of the dessicants, damage to parts or wafer tray due to forces on the evacuated pack
Electronics Forum | Tue Aug 19 09:09:15 EDT 2003 | D Peter
After a few problems and time constraints on baking moisture sensitive devices, we are looking at solutions to storage rather than going after a rebaking solution. One thing that always bothered me about baking was the oxidation on the lead finish,
Industry News | 2018-10-18 10:23:07.0
Typical RoHS Issues in PCB Assembly
Industry News | 2018-12-08 03:29:29.0
SMT Dictionary – Surface Mount Technology Acronym and Abbreviation
Technical Library | 2024-09-02 18:48:58.0
The conversion to higher temperature "Lead Free" assembly reflow conditions has created an increased awareness that entrapped or absorbed moisture is a frequent root cause of thermally induced delamination at assembly reflow. There are two connected failure modes from entrapped moisture; incomplete resin cross-linking resulting in premature resin decomposition and also severe Z axis expansion from "explosive vaporization of the entrapped moisture at elevated temperatures at assembly reflow". Ultimately, both result in delamination failure. Other papers have shown the negative effects of entrapped moisture before lamination including delamination, red color, reduced thermal reliability and increased high speed signal loss. In this paper, various materials were tested for moisture sensitivity during lamination. Tests were performed at varying lamination conditions including a pre-vacuum step and "kiss" step. Pressure and cure temperature parameters were evaluated for minimizing or eliminating the effect of trapped moisture. Also included are the results of inner layer moisture removal baking conditions and their effect on peel strength and thermal reliability.
Technical Library | 2021-11-26 14:34:07.0
The use of desiccant bags filled with Silica Sand and or Clay beads used in conjunction with a Moisture Barrier Bag to control moisture for storage of printed circuit boards has long been an accepted practice and standard from both JEDEC and IPC organizations. Additionally, the use heated ovens for baking off moisture using the evaporation process has also been a long#2;standing practice from these organizations. This paper on alternative drying methods will be accompanied by completed independent, unbiased tests conducted by Vinny Nguyen, an engineering student (now graduated) from San Jose State University. The accompanied paper will examine the performance levels of different technologies of desiccant bags to control moisture in enclosed spaces. The tests and equipment set were reviewed by an engineer and consultant to the Lockheed Martin Aerospace Division and the IPC - TM-650 2.6.28 test method was review by engineer from pSemi. The tests were designed to mimic performance tests outlined in Mil Spec 3464, which both IPC and JEDEC have adopted for their respective standards. The test examined variables including absorption capacity rates, weight gain and release of moisture back into the enclosed area. The presentation will also address and highlight: • Similarities of PCBs and Heavy Equipment as it applies to Inspections, Causes of Failure, Types of Corrosion and Moisture Collection Points. • Performance Attributes of Different Desiccant Technologies as it applies to shape, texture, change outs, labeling and regeneration. • Venn Diagram of Electromechanical Failure with the circles 1. Current 2. Contamination 3. Humidity Presentation Available
Imagineering, Inc. | https://www.pcbnet.com/blog/everything-you-need-to-know-about-moisture-sensitive-devices-msds/
What You Must Know About Moisture Sensitive Devices (MSDs) Skip to main content Resources Support Contact Us FAQs Live Chat My Account 847-806-0003 Menu PCB Capabilities Fabrication Technology Roadmap Materials Available HDI Tolerances Certifications
Heller Industries Inc. | https://hellerindustries.com/delamination/
. (Some practitioners pre-bake components and boards to drive out moisture. This is not encouraged and should be a last resort as baking tends to build intermetallics as well as degrade the solderability by increasing oxidation levels