Industry Directory | Consultant / Service Provider / Distributor / Equipment Dealer / Broker / Auctions / Manufacturer / Manufacturer's Representative
DONGGUAN KINGSUN AUTOMATION TECHNOLOGY CO.,LTD is a company which mainly provide used and new SMT parts, provide repair SMT key parts service,new/used SMT machine trading,SMT consumables and Peripherals equipment,Clean room, ESD..
Industry Directory | Manufacturer
DONGGUAN KINGSUN AUTOMATION TECHNOLOGY CO.,LTD is a company which mainly provide used and new SMT parts, provide repair SMT key parts service,new/used SMT machine trading,SMT consumables and Peripherals equipment,Clean room, ESD..
Cut panels without scoreline and with overhanging components. The S300 diamond blade depaneling saw is ideal for use in singulating assembled PCBs. Singulate panels up to 12" wide. Microprocessor controlled STI safety interlock Long Lasting Di
New Equipment | Education/Training
This program is for experienced solderers seeking an in depth knowledge of the J-STD-001 Document. The course reviews this document and helps students learn how to interpret the criteria. Open and closed book exams are required after each module. Han
Electronics Forum | Thu May 01 07:33:19 EDT 2008 | realchunks
Jim, You need to repair or by-pass the cover interlock. The machine thinks it's open and will not procede any further. They all do it, even the new models. Once you get past this warning - you will get the the RESET window - garanteed.
Electronics Forum | Wed Sep 27 17:49:41 EDT 2006 | SWAG
Open the rear door that has the cooling fans on it. Look at the wiper blade regulator, look toward the front of the machine about 8" or so and to then left 3"or 4". There should be a lexan cover/box over the board that has this pot. on it. If stil
Used SMT Equipment | Screen Printers
Substrate processing: Maximum substrate size (XxY): 609.6mmx508mm(24”x20”) For circuit boards larger than 20”, special fixtures are required Minimum substrate size (XxY): 50.8mmx50.8mm(2”x2”)
Used SMT Equipment | Pick and Place/Feeders
Concept: Over drive motion Ultimate access Super wide range DDH V5 Smart operation Voluntary line operation Wide open &Easy access Quick exchange Auto changeover PP type LISA Feeder hot swap Chip theory speed 84500chip Placement ra
Industry News | 2003-05-28 08:28:54.0
For June 2-4 (Mon. - Wed.)Design Automation Conference 2003
Industry News | 2009-09-26 15:37:45.0
Barry O’Brien died on Sunday, September 20, 2009 while bike riding. Barry covered the Ohio territory for Horizon Sales, a manufacturer’s representative corporation supplying machinery and supplies to the electronics industry.
Parts & Supplies | SMT Equipment
Vacuum channel opening and closing cylinder Name: P1928; vacuum channel opening and closing cylinder Part Number: P1928 Description: P1928 vacuum pump channel opening and closing cylinder Applicable models: UP; AP Printing Presses P1
Parts & Supplies | SMT Equipment
Vacuum channel opening and closing cylinder Name: P1928; vacuum channel opening and closing cylinder Part Number: P1928 Description: P1928 vacuum pump channel opening and closing cylinder Applicable models: UP; AP Printing Presses P1
Technical Library | 2019-05-29 01:47:22.0
1.Vias near SMD pads: Solder can flow into the via after melted. As a result cold joint will appear in the end. Check the picture below. 2.Vias on SMD pads: Solder can flow into the via more easier after melted. Check the picture below. 3.Via opening without soldermask covered. When workers solder TH parts by hand, soldering iron can touch vias sometime, then tiny amounts molten solder will stay on vias. This can lead to electrical short easily. We recommend you make all vias tenting (covered by solder mask) if it is possible.
PCBNPI-Professional PCB Fab/PCB Assembly Service Provider From China
Technical Library | 2017-08-17 12:28:30.0
At SMT assembly, flux outgassing/drying is difficult for devices with poor venting channel, and resulted in insufficiently dried/burnt-off flux residue for no-clean process. Examples including: Large low stand-off components such as QFN, LGA Components covered under electromagnetic shield which has either no or few venting holes Components assembled within cavity of board Any other devices with small open space around solder joints
Training Courses | | | IPC-6012 Specialist (CIS)
The Certified IPC-6012 Specialist (CIS) training covers design, fabrication and inspection of rigid printed boards.
Training Courses | | | IPC/WHMA-A-620 Specialist (CIS)
The Certified IPC/WHMA-A-620 Specialist (CIS) training focuses on cable and wire harness fabrication and installation.
Events Calendar | Tue Dec 08 00:00:00 EST 2020 - Tue Dec 08 00:00:00 EST 2020 | Online,
SMTA California Technology Day
Events Calendar | Wed May 31 00:00:00 EDT 2023 - Wed May 31 00:00:00 EDT 2023 | Holtsville, New York USA
Long Island Chapter Meeting: Fine Feature Paste Printing, Stencil Design and Solder Technology
Career Center | San Jose, California USA | Management
DCSI is one of the most trusted and respected global executive search and solutions companies inthe electronics manufacturing industries. We have more than 35 active openings that range from Managers, Directors, Sr. Directors, Vice Presidents, to EV
Career Center | Bolingbrook, IL USA | Production
Tellabs is in need of an individual who will be responsible for working in one or more varying functions within a printed circuit board product assembly process. Duties include automatic insertion, surface mount operation and Surface Mount Technolog
Career Center | Quito, Ecuador | Sales/Marketing,Technical Support
Technical Sales (machinery, animal and plant protection products). Sales Forecast New Products (Bsss Diffusion Model).
Career Center | Delton, Michigan USA | Engineering,Maintenance,Production,Technical Support
IPC Master instructor with a number of years experience in Engineering as well as Machine technician.
1st Place Machinery Inc. | http://www.firstplacemachinery.com/smt_pcb_screen_printers_mpmup100.html
MPM UP100 MPM UP-100 / Sigmanprint MV Stencil Printer Serial # 100834 Year ~ 2000 or newer 20" Stencil Capacity - Pneumatic Stencil locks Type
| https://www.feedersupplier.com/sale-13119451-p3251-mpm-printer-spare-parts-mpm-up2000-vision-card-mpm-p3251-up2000-vision-card.html
P3251 MPM printer SPARE PARTS MPM UP2000 VISION CARD MPM P3251 UP2000 vision card Leave a Message We will call you back soon! Your message must be between 20-3,000 characters
