New Equipment | Solder Paste Stencils
EasyBraid’s stencil rolls are designed for use in SMT screen printing lines which keep stencil apertures clear of paste residues during the automatic screen printing process. They also clean the bottom of stencils, keeping them free from paste and fl
New Equipment | Solder Materials
We have a wide variety of flux-Cored solder, a mix of metal alloy, flux and other elements, that we have put together to match every type of application. This formula is designed so that the incidence of bridging is rare; likew
Electronics Forum | Wed Apr 21 21:50:28 EDT 2004 | adam
Hi I recently having problems on the components having non wetting on the flex circuits. The profile that I am using is according to the solder paste suppiler recommended. Can anyone pls. advise? Regards
Electronics Forum | Wed Sep 15 20:59:23 EDT 2010 | genesan
hi All, Here i snap shot previous PCB(HASL) and current PCB(Immersion Silver).Base on the photo it could be PCB oxidize cause the non wetting?
.JPG)
Used SMT Equipment | SPI / Solder Paste Inspection
The LSM300 follows the successful Laser section Microscopes LSM and LSM2. This new non-contact laser based system is an off-Line solder paste inspection system.LSM300 provides automatic height measurements, eliminating the inconsistencies of manual m
Industry News | 2013-07-22 09:54:27.0
GPD Global has introduced its new NCM5000 dispense pump for easy jetting. With only two wetted parts and no seals or springs to replace or adjust, field operation is simple.
Industry News | 2013-09-10 12:18:26.0
The Surface Mount Technology Association (SMTA)'s Intermountain Chapter will hold its annual technical symposium on September 19 at the University of Utah in the Warnock Engineering Building, Salt Lake City, Utah.
Technical Library | 2023-08-04 15:27:30.0
A designed experiment evaluated the influence of several variables on appearance and strength of Pb-free solder joints. Components, with leads finished with nickel-palladium-gold (NiPdAu), were used from Texas Instruments (TI) and two other integrated circuit suppliers. Pb-free solder paste used was tin-silver-copper (SnAgCu) alloy. Variables were printed wiring board (PWB) pad size/stencil aperture (the pad finish was consistent; electrolysis Ni/immersion Au), reflow atmosphere, reflow temperature, Pd thickness in the NiPdAu finish, and thermal aging. Height of solder wetting to component lead sides was measured for both ceramic plate and PWB soldering. A third response was solder joint strength; a "lead pull" test determined the maximum force needed to pull the component lead from the PWB. This paper presents a statistical analysis of the designed experiment. Reflow atmosphere and pad size/stencil aperture have the greatest contribution to the height of lead side wetting. Reflow temperature, palladium thickness, and preconditioning had very little impact on side-wetting height. For lead pull, variance in the data was relatively small and the factors tested had little impact.
Technical Library | 2021-07-06 21:13:36.0
The surface finishes commonly used on printed circuit boards (PCBs) have an effect on solder paste performance in the surface mount process. Some surface finishes are non-planar like hot air solder level (HASL) which can lead to inconsistencies in solder paste printing. Other surface finishes are difficult to wet during reflow like organic solderability preservative (OSP). What is the overall effect of surface finish on solder paste performance? Which solder paste is best for each surface finish? It is the goal of this paper to answer these questions.
DescriptionThe Electrovert® Electra™ is an advanced, meticulously engineered wave soldering system designed for high-mass and high-volume manufacturers. Although intended for maximum throughput requirements, the Electra also offers maximum process fl
A Sustainable Alternative - Humitector cards are halogen-free and cobalt dichloride free. Visit https://www.clariant.com/solutions/products/2017/10/31/00/12/humitector-type-2-nonreversible-humidity-indicator-card?utm_source=CLRYouTube&utm_medium=Vi
Training Courses | | | PCB Assembly Courses
The PCB assembly courses provide knowledge of different processes and equipment used in TH and SMT assembly of printed circuit boards.
Career Center | Javalera, Gen. Trias, Cavite Philippines | Engineering
Numonyx is a semiconductor company making flash memories, which was founded on March 31, 2008 by Intel Corporation, STMicroelectronics and Francisco Partners. The company supplies non-volatile memory for a variety of consumer and industrial devices i
GPD Global | https://www.gpd-global.com/co_website/fluid-dispense-adhesive-application.php
Conductive Adhesive & Non-Conductive Adhesive Dispensing Home Products Fluid Dispensing Equipment High Precision Dispenser -MAX Series Large Format Board Dispensing -DS Series Table Top Dispensing Equipment Loader
.gif)
