New Equipment | Education/Training
BEST offers a one of a kind mobile training center which allows the students to be sequestered inside the training center without outside distrction. In addtion the mobile traiing enter on wheels is a comfortabel place to train where all of the most
New Equipment | Solder Materials
For high density and advanced package technology, We provide new Solder Paste for PoP applications. Package on Package Solder Paste has better wettability, solderability and low void than others.
Electronics Forum | Wed Oct 23 14:33:44 EDT 2002 | lhoang
Any one encountered the problem such as poor conductivity when the silkscreen mis-registrated on the solder pads ? Thanks; Linh
Electronics Forum | Sun Nov 03 08:28:29 EST 2002 | davef
We have had poor solderability from silk screen being on pads, but have never measured the conductivity.
Industry News | 2003-04-30 08:51:08.0
Electrolube played the role of environmental champion in Australia recently.
Industry News | 2011-01-18 13:20:51.0
Following on the very successful 2005 and 2006 International Conferences on Lead-free Soldering, and the SMTA International Conference on Soldering and Reliability held in Toronto, Ontario, Canada since 2007, this conference will bring together the community of soldering and reliability experts. Show off the expertise of your company by presenting a paper.
Parts & Supplies | Pick and Place/Feeders
Many companies first applied SMT second-hand placement machines, and the selected placement machines were relatively stable, with low failure rate, easy maintenance, and important maintenance costs. Therefore, there are still many concerns about buyi
Parts & Supplies | Pick and Place/Feeders
Many companies first applied SMT second-hand placement machines, and the selected placement machines were relatively stable, with low failure rate, easy maintenance, and important maintenance costs. Therefore, there are still many concerns about buyi
Technical Library | 2023-01-17 17:27:13.0
Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The degree of wetting, the microstructure (in particular the intermetallic layer), and the inherent strength of the solder all factor into the reliability of the solder joint. This paper presents experimental results on the effect of reflow profile on both 63%Sn 37%Pb (SnPb) and 96.5%Sn 3.0%Ag 0.5%Cu (SAC 305) solder joint shear force. Specifically, the effect of the reflow peak temperature and time above solder liquidus temperature are studied. Nine reflow profiles for SAC 305 and nine reflow profiles for SnPb have been developed with three levels of peak temperature (230 o C, 240 o C, and 250 o C for SAC 305; and 195 o C, 205 o C, and 215 o C for SnPb) and three levels of time above solder liquidus temperature (30 sec., 60 sec., and 90 sec.). The shear force data of four different sizes of chip resistors (1206, 0805, 0603, and 0402) are compared across the different profiles. The shear force of the resistors is measured at time 0 (right after assembly). The fracture surfaces have been studied using a scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS)
Technical Library | 2008-08-28 22:50:11.0
The increasing use of lead-free solder has introduced a new set of process parameters when setting up wave solder equipment for effective soldering. Determining the proper flow characteristics of the solder wave for adequate hole fill is an essential step in achieving a reliable process. A variety of solder waves exist in the industry; each with advantages and disadvantages when performing lead-free wave soldering. One way to ensure adequate hole-fill is by increasing contact time at the Chip Wave.
PCB vacuum suction loader/SMT vacuum loader for loading bare board on PCB assembly line: https://www.ascen.ltd/Products/Automatic_SMT_equipment/PCB_loader/123.html ASCEN PCB vacuum loader we produced is mainly used for the beginning of the SMT produc
EKT AOI machine application: inspection after stencil printing, pre/post reflow oven, pre/post wave soldering?FPC etc. Stencil printing: Solder unavailability, insufficient or excessive solder, solder misalignment, bridging, stain, scratch etc. Compo
SMT Express, Volume 4, Issue No. 5 - from SMTnet.com Volume 4, Issue No. 5 Thursday, May 23, 2002 Featured Article Return to Front Page Book Review Reviewed by Dave Fish (davef ), Pandion Electronics, Inc. Title: Reflow Soldering
| https://www.eptac.com/webinar/conformal-coating-and-solder-resist/
Q & A on Solder Resists and Conformal Coatings | EPTAC Skip to content Scroll Toll Free: 800.643.7822 Toggle navigation Training All Classes
Heller 公司 | http://hellerindustries.com.cn/Vacuum-Void-Reduction-Reflow.pdf
The Effect of Vacuum Reflow Processing On Solder Joint Voiding And Thermal Fatigue Reliability To be published in the Proceedings of SMTA International, September 17 - 21, 2016, Rosemont, IL
COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.
2481 Hilton Drive
Gainesville, GA USA
Phone: (770) 538-0411
