Nozzle Tech supply pick & place nozzles and component feeder refurb parts, such as, springs,feeder locating pins, air pins, guide rails etc. Nozzle Tech has supplied companies from around the world including Nokia, Motorola & Flextronics
ProntoVIEW-MARKUP is assembly CAD Viewer & Gerber Viewer software used by electronics manufacturers to quickly find components, pin, shorts between traces, etc. ProntoVIEW-MARKUP is also a redline tool that allows annotation of the assembly to creat
Low Cost Punch For Singulation Small Tab Routed Panels N200 singulates one tab at a time with upper and lower pinch blades. Singulate curve routed and odd shaped boards. Top and bottom knife set cuts tabs cleanly. Minimal stress on PCB. Toolin
Electronics Forum | Tue Oct 30 14:39:41 EST 2001 | markhoch
Has anybody else out there had problems with SMT connectors with plastic locating pins lifting up during the reflow process? We've had several instances with several differant types of SMT connectors lifting up during the reflow process. We've even g
Electronics Forum | Tue Oct 30 19:14:21 EST 2001 | davef
I'll ask you the same questions as this poster ... http://www.smtnet.com/Forums/index.cfm?fuseaction=view_thread&CFApp=1&Thread_ID=4627&mc=2
Used SMT Equipment | In-Circuit Testers
This equipment is located in our upcoming STS Online Auction - February 25 - 28, 2019 1 - Controller 2 - ASRU C Cards 2 - Control Xt Cards 18 - Hybrid DD Cards 2 - 6624A Power Supplies 1 - Pin Verification Fixture
Used SMT Equipment | SMD Placement Machines
* DOS * Flying Nozzle change * Fiducial camera * Pneumatic tape feeder * Locate Pin * Edge clamp * Z servo push plate * Entrance sub stop * Exit sub stop * Auto width adjust * Feeder float detection
Industry News | 2016-05-10 14:16:16.0
GPD Global offers individual pumps for integration into your existing platform – the Jetting NCM5000 Pump is one of them. The Jetting NCM5000 Pump simplifies jetting to its basic elements: hammer, pin, and nozzle. Only the pin and nozzle are wetted parts. This means easy set-up, cleaning, and upkeep.
Industry News | 2017-03-09 22:28:20.0
GPD Global introduces its NEW Conformal Coating System (SimpleCoat), an Inline and Cost-effective Conformal Coating System with full featured programming - making conformal coating processes quick and easy.
Parts & Supplies | SMT Equipment
YAMAHA YV100XG locating pin KGA-M9174-10X KGA-M9172-00X Yamaha Air Valve A010E1-37W KM1-M7163-20X Yamaha Air Valve A010E1-54W KM1-M7163-21X Yamaha Air Valve A010E1-44W KM1-M7163-30X Yamaha Valve A010E1-35W KM1-M7162-20X Yamaha Valve A010E1-55W
Parts & Supplies | Assembly Accessories
YAMAHA YV100XG locating pin Part Number : KGA-M9174-10X KGA-M9172-00X More Yamaha parts in stock KM9-M7107-00XSHFT, HEAD ASSYYV100II KM9-M7106-00XSHAFT HEAD ASSY YV100II KV8-M713S-A0X STD.SHAFT2,SPARE YV100X KV8-M712S-A0X STD.SHAFT
Technical Library | 2019-12-05 13:30:46.0
Conformal coatings are regularly employed to protect the surface of a soldered printed circuit board assembly from moisture, chemicals in the PCBA's service environment, and foreign objects or debris. Conformal coatings are nonconductive and therefore cannot be placed on any location where electrical contact will be required, such as connector pins, test points, and sockets. Conformal coatings are also not permitted on any mechanical interface location, such as mounting holes or brackets, to assure the proper fit between items in the final assembly. In order to apply conformal coatings to an assembly and comply with the restrictions on keep-out areas, masking is employed to protect those surfaces.
Technical Library | 2019-06-07 14:49:54.0
ACI Technologies was contacted in regards to poor solder joint reliability. The customer submitted an assembly that was exhibiting intermittent opens at multiple locations on a ball grid array (BGA) component. The assembly’s functionality did not survive international shipping, essentially shock and vibration failures, immediately making the quality of the solder joints suspect. The customer was asked about the contract manufacturer and the reflow oven profile as well as the solder paste and surface finish used. The ACI engineering staff evaluated the contract manufacturer’s technique and determined that they were competent in the methods they used for placing thermocouples in the proper locations and developing the reflow oven profile. The surface finish was unusual, but not unheard of, in that it was hard gold over hard nickel, rather than electroless nickel immersion gold (ENIG). The customer was able to supply boundary scan testing data which showed a diagonal row of troublesome BGA pins.
http://www.gpd-global.com No drip no drool across a wide range of fluid viscosities (low-to-mid and low-to-high). No manual adjustment to compensate for pump variability. Truly Volumetric PCD Pumps for total control of dispensing fluids. Ability to
we have many hitachi equipment and hitachi feeders to sell . if you want to know more , please contact us tina@smtfeeders.cn
Career Center | Sherman, Texas USA | Engineering,Production,Research and Development,Technical Support
SMT Packaging Engineer: Location: Texas - Sherman , TX Group: HVAL Degree Requirements: BS ME/ChemE/Materials The person in this position will have the ability to make very significant financial contributions to TI because this is a very critic
Career Center | Alleppey, Kerala India | Engineering,Production,Quality Control
Good knowledge about the operations of various PCB surface mounting machines Good communication skills
Career Center | , | 2014-01-31 02:17:45.0
Good knowledge about the operations of various PCB surface mounting machines Good communication skills
The Pin-in-Paste (or AART) Process for Odd Form and Through Hole Printed Circuit Boards The Pin-in-Paste (or AART) Process for Odd Form and Through Hole Printed Circuit Boards Universal Instruments Credit/Source: Jay B. Hinerman, K. Srihari, Ph
FKN Systek | http://fknsystek.com/8DSN200.pdf
. Minimal stress on PCB. Tooling pins adjustable in X and Y direction. Custom tooling available. Turn Knob to Bring Pins Forward Drop in locating pin dies for a variety of PCB types
KingFei SMT Tech | https://www.smtspare-parts.com/sale-10641063-smt-spare-parts-cp6-3-0-smt-nozzle-for-fuji-machine-cp642-cp643.html
3.7 mm - 16 mm Sq Disk-Ft Lt ADCPH-9650 5.0 mm - 16 mm Sq Disk-Ft/Bk Lt ADCPH-9660 5.0 mm - 16 mm Disk-Bk Lt Miscellaneous FUJI Parts GPD-0360 D-Table Locating Pin CP-2
