High-Tech staffing firm, specializing in placeing ASIC and Hardware engineers.
Industry Directory | Manufacturer
Stencil Point is the ISO/ROHS/CE & ISO complianced company. We are the manufacturer and exporter of Laser Cut Stencils for SMD Component Mounting / Pick & Place Machines.
Equipped with the nozzle library exchange station, the size of the material can be mounted by a single machine. >Standard pallet material station, braided pallet material can be mounted at the same time. >Eight separate gigabit network port industr
KS6V LED Placement Machine Domestic Applicable to: fluorescent tubes,flexible light strips,flat lights,outdoor lights,ceiling lights, bulbs,terminals,power supplies,etc. Product name 6V (six head placement machine)
Used SMT Equipment | Pick and Place/Feeders
YAMAHA i-PULSE M7-3L SMT machine Placement speed:65,000 points per hour Long substrate size: : L1290 x W410mm Component processing range :01005 to 23mm sq IC Dimension of equipment :L1,990 x
Used SMT Equipment | Pick and Place/Feeders
Product number: RX - 6 Detailed product introduction Characteristic： With high productivity, versatility, highquality new modular placement machine RX - 6 listed Draw/monitor corresponding patch Components in speed Chip components: 42000 CPH *
Industry News | 2018-10-08 20:18:03.0
GPD Global will exhibit at the upcoming SMTA International 2018. At booth# 517, see our automated Conformal Coating Machine with excellent repeatability for under $40,000.
Industry News | 2003-06-12 08:24:37.0
An adaptive tool prevents small and/or light components "lifting" or "floating" on printed circuit board assemblies during the wave solder process.
Technical Library | 2019-11-12 02:09:22.0
Thermal shock test chamber can be used for testing the chemical change or physical damage on composite materials caused by the thermal expansion and contraction of the sample in the shortest time,which is subjected to extremely and continuous high and low temperature environment.so how to check the temperature recovery time of this chamber? Normally we take following steps to inspect the temepratuire recovering time: 1.Install the temperature sensor at the specified position, and adjust the temperature controller of hot zone and cold zone to the required nominal temperature respectively. 2.The temperature increases and reduces respectively,30min after temperature in two zones reach stable status,record temperature value of the measuring point,pls set the temperature value of two zones to be required nominal temperature. 3.The temperature shock test chamber automatically places the inspected load into theh ot zone,select the corresponding retention time according to regulated standard. 4.Set the transfer time,then the inspection load is transferred from hot zone to cold zone, and the temperature of the measuring point is observed and recorded, and then the reverse conversion of the load from cold zone to hot zone is carried out according to the same method, and the temperature of the measuring point is observed and recorded. www.climatechambers.com
Technical Library | 2019-11-17 22:46:45.0
Overview of walk-in temperature and humidity chamber: It also belongs to environmental test equipment, it tests whether the product can resist high temperature, low temperature, humidity, or the physical and chemical changes produced under extreme conditions, the walk-in temperature and humidity chamber volume is large, the product is placed, or a large object can be placed, such as automobile, new energy, television and liquid crystal screen, etc. How to do the routine maintenance of the walk-in temperature and humidity chamber: 1. The wet gauze basically, if there is no special case, s/b usually changed once in 3 months 2. The water channel shall be regularly cleaned, including water cup, water tank, etc., so as to prevent the water from being blocked,affect the humidity test. 3. It is forbidden to test the flammable and explosive products inside working room. 4. Clean the chamber on a regular basis 2. How to operate walk-in temperature and humidity chamber: The operation method is same as standard temperature humidity test chamber,the controller is 7-inch LCD programmable color screen, you only need to setthe temperature point---test time--how many cycles need to be tested, This can be done automatically, and the machine will stop automatically when it is complete. If there is any problem during the operation, the corresponding problem point will be displayed on the machine control screen. Walk-in temperature and humidity chamber is a must equipment for reliability test of Automobile,Aerospace,Electronic parts,etc,the operation and maintenance are easy,it is teh tear down mahcine,Climatest engineers will be dispatched to do on-site support,for instance,we will finish commissioning,train customers how to operate,maintain,welcome to follow our company facebook page:https://www.facebook.com/Climatechambers
Equipped with the nozzle library exchange station, the size of the material can be mounted by a single machine. >Standard pallet material station, braided pallet material can be mounted at the same time. >Eight separate gigabit network port industr
KS6V LED Placement Machine Domestic Applicable to: fluorescent tubes,flexible light strips,flat lights,outdoor lights,ceiling lights, bulbs,terminals,power supplies,etc. Product name 6V (six head placement machine)
Training Courses | | | PCB Design Courses
The PCB design courses teach students the process, techniques and tools needed to design layout of printed circuit boards.
Events Calendar | Mon Feb 03 18:30:00 UTC 2020 - Wed Feb 05 18:30:00 UTC 2020 | San Diego, CA, California USA
IPC APEX EXPO 2020
Events Calendar | Tue May 06 18:30:00 UTC 2025 - Thu May 08 18:30:00 UTC 2025 | Munich, Germany
Power2Drive Europe
Career Center | Santa Clara, California USA | Engineering,Research and Development
Fabless Semiconductor company is seeking a Place and Route engineer to do floor planning, computer place and route, and generate clean layout after. Expert in Apollo.
Career Center | Santa Clara, California USA | Engineering
Fabless Semiconductor company is seeking a Place and Route engineer to do floor planning, computer place and route, and generate clean layout, and netlist after. Expert in Apollo and Clock Tree.
Career Center | Santa Maria, Canillo | Engineering,Maintenance,Management,Production
Over 10 years experience in computers, including IBM, Apple, and software. Microsoft: Windows/DOS, all versions. Office Pro, including Excel, Access, Word, PowerPoint and Publisher, all versions. Visual Basic 6. Other: Adobe Page/FrameMaker. L
Career Center | clearfield, Utah USA | Maintenance,Management,Production,Quality Control
Jeffrey Barnaby 612E 2100 S. Clearfield, UT 84015 Phone: 801-564-4432 Email: barnabyysb@yahoo.com OBJECTIVE: A challenging position with a stable organization, where I can utilize my past experience, and be given an opportunity to further adva
| http://www.feedersupplier.com/sale-13929584-asm-siemens-siplace-power-00353277-adjusting-gauge-for-star-0-point-dlm1.html
Asm Siemens Siplace Power 00353277 Adjusting Gauge For Star 0 Point Dlm1 Basic Information Place of Origin: Germany Brand Name: ASM SIEMENS SIPLACE Model Number
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/sealant-equipment/products/valves/foam-in-place-valve
Foam-in-Place Valve Data Sheet Foam-in-Place Valve Nordson Sealant Equipment's Foam-in-Place Valve controls two-component foam materials at point of dispense with no drool, pressure spikes or mixing irregularities
