World leader in Load Cells, Torque Sensors, Pressure Sensors, Signal Conditioners, Digital Displays, and Sensor System products. The one stop source for all your sensor needs. Custom design available. Well-known for short lead-time & customer support
FUTEK Model L2357 Series load cells, also known as S-Beam Jr., are the world�s most compact and lightest �S� or �Z�-beam load cells with the highest accuracy in linearity. Unique features include overload protection up to 1000% of the RO in both Tens
New Equipment | Test Equipment
The Fluke 5790A AC Measurement Standard is a Complete automated ac measurement standard designed for the most demanding calibration applications. It combines the accuracy you would expect from a thermal transfer standard with the ease-of-use of a dig
Electronics Forum | Sat Apr 25 08:48:45 EDT 1998 | raymond
Is there an industry standard in calculating SMT process PPM level for benchmarking purpose ? What are the industry benchmark ppm number for some of the defects like solder short for 20-mil QFP, tomstone problem for 0603 components etc....
Electronics Forum | Sun Mar 22 15:29:01 EST 1998 | Michael Fogel
What is the right way to count the opportunities for defects in order to calculate the quality (in ppm) of SMT assembly processes as well as the quality of the PCB's? Please replay to: fogel_m@netvision.net.il or micha.fogel@ecitele.com
Used SMT Equipment | In-Circuit Testers
Fluke 5790A-03 Automated AC Measurement StandardAutomated AC Measurement Standard The 5790A is a complete automated ac measurement standard designed for the most demanding calibration applications. It combines the accuracy you would expect from a the
Used SMT Equipment | Soldering - Reflow
Note the defect!KE68008521 - Calculator German MaxireflowKE68008130 - Acoustic alarm function (‘horn’) In addition to the red warning light, an acoustic signal is emitted in the event of an alarm.KE68008110 - Wind vane relay for monitoring the ext
Industry News | 2012-05-23 14:18:26.0
Joint Industry Guideline Provides Best Practices for Measuring the Strain on Boards and Components During Manufacturing
Industry News | 2018-12-08 03:35:10.0
Top 10 Consumer Electronics Companies in the World
Technical Library | 1999-05-07 10:14:57.0
This paper describes a model developed to calculate number of redundant good die per wafer. A block redundancy scheme is used here, where the entire defective memory subarray is replaced by a redundant element. A formula is derived to calculate the amount of improvement expected after redundancy. This improvement is given in terms of the ratio of the overall good die per wafer to the original good die per wafer after considering some key factors.
Technical Library | 2023-08-02 18:18:23.0
As six sigma (6) and better processes are demanded for higher yields and as organizations move from measuring defects in terms of parts-per-million (ppm) towards parts-per-billion (ppb), the resolution of extant control charts is becoming insufficient to monitor process quality. This work describes the development of a new statistical process control (SPC) chart that is used to monitor processes in terms of defects-per-billion-opportunities (dpbo). A logical extension of the defects-per-million-opportunities (dpmo) control chart, calculations used to derive the dpbo control limits will be presented and examples of in-control and out-of-control processes will be offered.
Career Center | Corpus Christ, Texas USA | Engineering,Quality Control
This position reports to the Quality Manager and provides support in all areas of fabrication and assembly of passive components exceeding customer requirements and expectations in a fast paced environment. Support is defined as but not limited to th
Career Center | Houston, Texas USA | Engineering,Management,Quality Control,Technical Support
Seasoned Process & Quality Engineer. Degreed Chemical Engineer. 20+ years in Electronics Semiconductor manufacturing. Proficient in Quality Statistical tools, Design of Experiments, FMEAs, APQP, PPAP, ISO 9000, ISO/TS 16949 etc.
GPD Global | https://www.gpd-global.com/co_website/pdf/lead-former/CF8-Calculator-Software-Guide-8201622.pdf
dies are allowed in that station for the selected form, a list will appear. Use the [Up 8] and [Down 9] to select a die and press [Enter]. Then press [F1] to recalculate the station settings. CF-8 Formula Calculator 12/04/95 10 When the calculation is
| http://etasmt.com/cc?ID=te_news_bulletin,16961&url=_print
. Here to share a calculation formula of capacity: Capacity = PCB Length * 60sec / Chain Speed Chain Speed = Heat Zones Length / Cross Time
winsouce.jpg)
