Industry Directory | Consultant / Service Provider / Manufacturer / Other
Taiwan Dry Tech Corp. manufacturer of Eureka Dry Tech Fast Super Dryers for moisture/humidity proof protective storage of PCB, MSD, IC packages, meets IPC/JEDEC J-STD-033 & IPC-1601.
Industry Directory | Consultant / Service Provider / Manufacturer
Eureka Dry Tech's IPC/JEDEC J-Std-033c Ultra Low Humidity Dry Cabinets provides moisture/humidity controlled storage of MSD，PCB, IC packages. Drying technology trusted by millions in replacing baking, nitrogen & desiccant packs.
New Equipment | Board Handling - Storage
Eureka SDC-101 Fast Super Dryer Ultra Low Humidity Dry Cabinet Specs: http://eurekadrytech.com/fast-super-dryer/sdc-101 Anti-static Glass, Anti-static Paint on Body and Shelves, Anti-static Stands, 1 M ω Ground Wire Model: SDC-101 Fast Super Drye
New Equipment | Board Handling - Storage
SDC-1001 Fast Super Dryer Ultra Low Humidity Dry Cabinet Specs: Model: SDC-1001 Fast Super Dryer Capacity: 657 Liters Humidity Range: LESS THAN 10% Recovery Time: Recovers to ≤ 10% RH within 30 minutes after accessing door for 30 seconds or less. Ex
Electronics Forum | Mon Jul 16 12:03:42 EDT 2007 | davef
We're aware of no industy acceptance standard for max moisture content of a board. For more on moisture levels, get a copy of: "Removing Moisture from Electronic Components and Assemblies", CS Leech, Jr, Circuits Assembly, May 1994. The article disc
Electronics Forum | Mon Dec 31 09:00:06 EST 2001 | davef
Baking before assembly does nothing good. It: * Increases costs. * Adds steps to the process and makes scheduling more cumbersome. * Increases the amount corrosion on solderable surfaces. We used to bake to remove the moisture from boards that caus
Used SMT Equipment | Soldering - Reflow
TrioTek: Ultraviolet UV Curing, IR Thermal Curing, Moisture Curing for encapsulants, adhesives, conformal coatings and potting compounds TrioTek™ inline curing ovens from ETS are ideal for medium to high-volume curing or drying of encapsulants, con
Used SMT Equipment | Coating and Encapsulation
Asymtek C-740 Century Series Conformal Coating System The Century® C-740 Series Selective Conformal Coating system provides consistent, uniform dispensing of a variety of conformal coating materials for inline coating applications. The system v
Industry News | 2003-03-24 09:46:41.0
Will feature a number of new technologies of interest to fabricators in printed circuit materials, laminate materials, polymer thick films and, most notably, its newest product line of embedded passive materials, DuPont Interra�.
Industry News | 2010-09-13 15:36:15.0
IPC — Association Connecting Electronics Industries® has released IPC-1601, Printed Board Handling and Storage Guidelines. The industry's sole standard on the handling, packaging and storage of printed boards, IPC-1601 provides users with guidance on how to protect printed boards from contamination, physical damage, solderability degradation, electrostatic discharge and moisture uptake.
Parts & Supplies | Soldering - Wave
Overseas Agent and Distributor Wanted ! Features : Spray Fiuxer: 1) Oriental motor drives the flux spraying system. Spraying speed is adjusted according to PCB board width and moving speed to ensure even spraying all time. 2) Durable “Meiji
Technical Library | 2020-11-29 22:06:45.0
Plastic laminates are increasingly used as interposers within chip packaging applications. As a component within the package, the laminate is subjected to package moisture sensitivity testing. The moisture requirements of chip packaging laminates are related to ambient moisture absorption and thermal cycling. Printed wiring board (PWB) laminates, however, are gauged on properties relating to wet processes such as resist developing, copper etching, and pumice scrubbing. Consequently, printed wiring board moisture absorption test methods differ from chip packaging test conditions.
Technical Library | 2024-09-02 18:48:58.0
The conversion to higher temperature "Lead Free" assembly reflow conditions has created an increased awareness that entrapped or absorbed moisture is a frequent root cause of thermally induced delamination at assembly reflow. There are two connected failure modes from entrapped moisture; incomplete resin cross-linking resulting in premature resin decomposition and also severe Z axis expansion from "explosive vaporization of the entrapped moisture at elevated temperatures at assembly reflow". Ultimately, both result in delamination failure. Other papers have shown the negative effects of entrapped moisture before lamination including delamination, red color, reduced thermal reliability and increased high speed signal loss. In this paper, various materials were tested for moisture sensitivity during lamination. Tests were performed at varying lamination conditions including a pre-vacuum step and "kiss" step. Pressure and cure temperature parameters were evaluated for minimizing or eliminating the effect of trapped moisture. Also included are the results of inner layer moisture removal baking conditions and their effect on peel strength and thermal reliability.
Training Courses | | | PCB Inspection Courses
The PCB inspection courses focus on improving PCB yield and reliability through validation and detection of defects on electronics assemblies.
Events Calendar | Tue Apr 13 00:00:00 EDT 2021 - Tue Apr 13 00:00:00 EDT 2021 | ,
Boston Chapter Webinar: Cleaning Chemistry For PWB and Rework - Part 2, session 1
Events Calendar | Tue Apr 13 00:00:00 EDT 2021 - Tue Apr 13 00:00:00 EDT 2021 | ,
Boston Chapter Webinar: Cleaning Chemistry For PWB and Rework - Part 2, session 2
INSERT INTO tracking_express (userid, username, page_id, ts) VALUES ('#Quser_profile.id#', '#Quser_profile.username#', 99, (#ts#)) SMT Express, Volume 4, Issue No. 2 - from SMTnet.com Volume 4, Issue No. 4 Thursday, April 18, 2002 Featured
INSERT INTO tracking_express (userid, username, page_id, ts) VALUES ('#Quser_profile.id#', '#Quser_profile.username#', 99, (#ts#)) SMT Express, Volume 4, Issue No. 2 - from SMTnet.com Volume 4, Issue No. 3 Thursday, March 21, 2002 Featured
Imagineering, Inc. | https://www.pcbnet.com/blog/how-to-prevent-a-solder-ball-defect/
. True to their name, they are a ball of solder that has separated from the main body that forms the joint fusing surface mount components to the board
| https://www.eptac.com/wp-content/uploads/2021/11/webinar_eptac_10_21_09.pdf
Synergy meeting covered 40 comments 16 IPC-A-610 Section on wireless wrap was discussed from the perspective of removing it from the 610 document as well as the 620 document and creating a downloadable document covering the total wireless wrap topic
