Industry Directory | Manufacturer
Manufacture defluxers, cleaners & maintenance solutions used to remove solder paste, flux residues, SMT Adhesives and other soils during the manufacture of electronic components or during the assembly of printed circuit boards.
Industry Directory | Manufacturer
Nitrogen Cast Lead Free solder Manufacturer, complete range of No Clean and No Residue fluxes Misprint Cleaning Systems completely compressed air driven low cost with no need for electrics 18x12
New Equipment | Rework & Repair Equipment
The new inspection mirror meets clean room requirements yet is sufficiently economical for non-clean room applications. A quality tool for the technician but inexpensive enough to meet the budgetary requirement of modern manufacturing. Economical Br
New Equipment | Solder Paste Stencils
Eliminate hours of solder mask damage repair time for bga sites while improving rework yield. Are you frustrated by the time it takes to repair mask damage underneath the BGA during the rework process? Are you squeezed for space on the PCB in an
Electronics Forum | Tue Jul 28 07:42:07 EDT 2009 | Mike Konrad
Hi Sean, No-clean flux does leave a residue. Under the best conditions, it is invisible. There are many factors that can cause the residue to become visible such as an inadequate oven profile (or lack of proper preheat on a wave). Also, if wave s
Electronics Forum | Tue Jul 28 01:39:32 EDT 2009 | Sean
Hi All, I have some question about flux residue resulted from non clean process as following: 1) Under what kind of circumstances that flux residue could appear? This residue does not happen during production but did appear after some period of ti
Used SMT Equipment | SMT Equipment
Product name: KD - 775 JUKI chip mounter Product number: KD - 775 Products in detail JUKI KD775 high-speed daub glue standard equipped with three dispensing head, achieved 0.1 seconds/launch daub adhesive at a high speed. Stable quality stand
Used SMT Equipment | Pick and Place/Feeders
Product number: KD - 775 Products in detail JUKI KD775 high-speed daub glue standardequipped with three dispensing head, achieved 0.1 seconds/launch daub adhesiveat a high speed. Stable quality standards are equipped witheven daub glue residual wi
Industry News | 2012-05-11 20:35:45.0
Heller Industries has been awarded a 2012 SMT VISION Award in the category of Soldering Reflow for its 1936 Mark 5 Reflow Oven. The award was presented on April 25, 2012 at the Nepcon China Exhibition.
Industry News | 2003-04-30 08:51:08.0
Electrolube played the role of environmental champion in Australia recently.
Parts & Supplies | Pick and Place/Feeders
Base size Max 410 × 360mm Min 50 × 30mm Smudge speed 0.1 seconds / launch(best conditions) Smudge accuracy ± 0.15 mm Needle type 30cc Set the smear angle 0 ° ~ 359 °(1 ° unit) A redesigned dot head. The standard
Parts & Supplies | Pick and Place/Feeders
The definition of SMT SMT is the surface assembly technology,surface mount technology(surface mount technology)(Surface Mounted Technology abbreviation),is currently the most popular electronic assembly industry,a technology and technology. What a
Technical Library | 2023-09-13 12:45:24.0
Improve the reliability of your electronics with our Offline PCBA Cleaning Machine. Achieve spotless, residue-free PCBAs for enhanced performance.
Technical Library | 2020-03-09 10:50:17.0
A customer called the Helpline seeking advice for cleaning no-clean fluxes prior to applying a conformal coating. The customer's assemblies were manufactured with a no-clean rosin based solder paste (ROL0) and were cleaned with an isopropyl alcohol (IPA) wash. After cleaning, a white residue was sometimes found in areas with high paste concentrations and was interfering with the adhesion of the conformal coating (Figure 1). For conformal coatings to adhere properly, the printed circuit board (PCB) surface must be clean of fluxes and other residues. In addition, ionic contamination left by flux residues can lead to corrosion and dendrite growth, two common causes of electronic opens and shorts. Other residues can lead to unwanted impedance and physical interference with moving parts.
Flux spray coating on a PCB with uniformal thickness down to 5 microns, with clear edge definition and minimal overspray. Can coat large or shoot dots with the same jet.
ACI Technologies Inc. (ACI) is a scientific research corporation dedicated to the advancement of electronics manufacturing processes and materials for The Department of Defense and industry. This video provides an overview of our commercial service
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Training Courses | ONLINE | | PCB Assembly Courses
The PCB assembly courses provide knowledge of different processes and equipment used in TH and SMT assembly of printed circuit boards.
Events Calendar | Tue Apr 14 00:00:00 EDT 2020 - Tue Apr 14 00:00:00 EDT 2020 | ,
Why Are We Cleaning No-Clean?
Events Calendar | Wed Aug 19 00:00:00 EDT 2020 - Wed Aug 19 00:00:00 EDT 2020 | ,
DfR - Design for Rinse-Ability: Effect of SMT Component Package Design on Cleaning Effectiveness
Article Return to Front Page No-Residue Technolo
| https://pcbasupplies.com/wp-content/uploads/2023/10/S3X58-M650-7-solder-paste.pdf
S3X58-M650-7 Halogen free pin testable solder paste Flux residue of conventional solder paste tends to deposit over the solder joint, and could lead to errone- ous readings in ICT evaluation even when
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/efd/products/solder-paste/fluxplus-paste-flux
. NC residue is clear, hard, noncorrosive, non-conductive, and designed to be left on your assembly. Residue may be removed with an appropriate solvent. Water Soluble (WS