Industry Directory | Manufacturer
Heller Thermal Systems India location featuring reflow soldering ovens and pressure curing ovens.
Industry Directory | Manufacturer
Rommtech-3S is your partner for reliable and cost effective contract manufacturing!have more than 15 years experience in the production of electronic and electromechanical devices � security products, radiators; cash registers manufacturing; igniters
New Equipment | Solder Materials
Tokyo, Japan – Koki Company Limited, global manufacturer and supplier of soldering materials, announces the release of new low Ag containing halogen free solder pastes that secures the equivalent joint reliability and heat profile to SAC305, namely S
New Equipment | Solder Materials
As the world's leading developer of advanced solder paste materials, Henkel delivers decades of technology and expertise for optimized process performance. With ground breaking new formulations to provide an easy transition to lead-free as well as pr
Electronics Forum | Thu Feb 15 10:48:34 EST 2007 | ck_the_flip
Is there anybody out there doing this scenario: SAC 305 Reflow & SN100C Wave and Selective Can the 2 alloys be mixed on 1 board, say, SAC 305 for SMT, and SN100C for thru-hole? Are 2 different rework chemistries needed, or can one use SN100c wire
Electronics Forum | Tue Feb 20 16:42:31 EST 2007 | ratsalad
We have been using SAC 305 for reflow and Cobalt 995 (very similar to SN100C, only cheaper) for wave and rework for quite a while now with no issues that I'm aware of.
Used SMT Equipment | Soldering - Selective
• Less then 100 hours • Stand-alone Machine • 2 Spray Nozzles/Programable • Dual Solder pots / Dual Heads – Loaded with SAC305 • Heads can run 4 different assembles • Pot level detection / Upgraded self-feeder • Automatic solder refill / Autom
Used SMT Equipment | Soldering - Reflow
Under 1,000 hours on this 7 zone reflow oven. Has edge rail only, no mesh belt and nitrogen. New 8-2012. Was only used in a semiconductor manufacturer’s clean room with SAC 103 solder. Is in like new condition. 480 volt, 3 ph. 100 amps. S
Industry News | 2005-09-19 16:07:56.0
No higher temperature and No process changes needed
Industry News | 2018-10-18 08:36:26.0
How the modern solder reflow oven works?
Parts & Supplies | Pick and Place/Feeders
KHY-M221A-A0 KGT-M221A-A0 YAMAHA YG12 tank chain gland KHY-M2267-00 YG12 tank chain YS12 towline keel X axis PISCO SP2550 R75 KHY-M2276-S0 YS12 screw X-axis YG12 X-axis screw YG12F YS12F screw guide KHY-M371R-00 RAIL GUIDE 12P YS24 YS100 Feida pl
Parts & Supplies | Other Equipment
C20-CPU84-E C200H-CPU01 C2000HCPU01E2V C2000HCPU0IE2V1 C200H-CPU02 C200H-CPU03 C200h-CPU11 C200H-CPU21 C200HCPU3E2 C200H-CPU31 C200HCPU31E2 C200HS-CPU01 C200HS-CPU21 C200HS-CPU31 C200HE-CPU11 C200HE-CPU32 C200HE-CPU42 C200HG-CPU33 C200HG-CP
Technical Library | 2023-01-17 17:27:13.0
Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The degree of wetting, the microstructure (in particular the intermetallic layer), and the inherent strength of the solder all factor into the reliability of the solder joint. This paper presents experimental results on the effect of reflow profile on both 63%Sn 37%Pb (SnPb) and 96.5%Sn 3.0%Ag 0.5%Cu (SAC 305) solder joint shear force. Specifically, the effect of the reflow peak temperature and time above solder liquidus temperature are studied. Nine reflow profiles for SAC 305 and nine reflow profiles for SnPb have been developed with three levels of peak temperature (230 o C, 240 o C, and 250 o C for SAC 305; and 195 o C, 205 o C, and 215 o C for SnPb) and three levels of time above solder liquidus temperature (30 sec., 60 sec., and 90 sec.). The shear force data of four different sizes of chip resistors (1206, 0805, 0603, and 0402) are compared across the different profiles. The shear force of the resistors is measured at time 0 (right after assembly). The fracture surfaces have been studied using a scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS)
Technical Library | 2023-09-07 14:38:31.0
A repeat customer specializing in high-technology interconnect, sensor, and antenna solutions, partnered with us to dispense small volumes of solder paste (Indium 10.1 SAC305 T6SG 78%m) onto backplane connectors – gold pads 0.175mm x 0.225mm. We performed a test requiring 0.200mm diameter or smaller dots to demonstrate the dispensing capability required.
SN100C P810 D4????????? ???????????? ??????????????????????????????????? ?????????????? ???http://www.nihonsuperior.co.jp/
ALPHA® Preforms with solder paste adds solder volume.
Career Center | Lakewood, California USA | Engineering,Maintenance,Management,Production
Quality conscience, detail oriented, manufacturing engineer, with a hands on approach to overall process improvement and development. Motivated with excellent communication skills and a dedicated team player. Qualifications include: � Safety /Diver
Career Center | Rochester, New York USA | Engineering
I have done my undergraduate studies in Mechanical Engineering. I am pursuing my Master's Program in Electronics Packaging. I am currently working as a Research Assistant for RIT-CEMA (Center for Electronics Manufacturing and Assembly). My research
be an optimal alloying addition in lead-free SAC (
Effect of Soldering Parameters on Reaction Kinetics and Phase Transformations of SAC 305 Solder Effect of Soldering Parameters on Reaction Kinetics and Phase Transformations of SAC 305 Solder As technology becomes increasingly reliant
Heller Industries Inc. | https://hellerindustries.com/browse/page/305/
Full List of Heller Reflow Ovens & Equipment Spare Parts - Heller Home » Full List of Heller Reflow Ovens & Equipment Spare Parts Heller Reflow Equipment Spare Parts Enter a part number or description
Heller 公司 | http://hellerindustries.com.cn/Vacuum-Void-Reduction-Reflow.pdf
The Effect of Vacuum Reflow Processing On Solder Joint Voiding And Thermal Fatigue Reliability To be published in the Proceedings of SMTA International, September 17 - 21, 2016, Rosemont, IL
.gif)
