Industry Directory | Manufacturer
Manufacturer of PCB depaneling and PCB soldering machines since 2005, products include CE approval V-groove PCB depanelizer, PCB router, PCB punching machine, laser depaneling, hot bar soldering machines and soldering robots.
Industry Directory | Consultant / Service Provider / Manufacturer
Good day! We have more than 21 years in the design and manufacturing of full and semi-auto PCB router and laser Separator and soldering machine. S1@smtfly.com
New Equipment | Solder Paste Stencils
Eliminate hours of solder mask damage repair time for bga sites while improving rework yield. Are you frustrated by the time it takes to repair mask damage underneath the BGA during the rework process? Are you squeezed for space on the PCB in an
New Equipment | Solder Paste Stencils
MPM UP2000 HiE Screen Printer Substrate treatment Minimum/maximum size 2"x 2"(50.0 mm x50.0 mm) to 20" x 16" (508 mm x 406 mm)(16 "or larger substrate requires special clamps
Used SMT Equipment | AOI / Automated Optical Inspection
Placement and solder joint inspection (reflow and wave soldering) Orthogonal camera module 8M (white LEDs): Field of view: 57.6 x 43.5 mm Resolution: 23.5 µm (standard), 11.75 µm (high) switchable with On Demand HR Number of mega pixel cameras:
Used SMT Equipment | Soldering - Selective
• Less then 100 hours • Stand-alone Machine • 2 Spray Nozzles/Programable • Dual Solder pots / Dual Heads – Loaded with SAC305 • Heads can run 4 different assembles • Pot level detection / Upgraded self-feeder • Automatic solder refill / Autom
Industry News | 2003-06-10 08:39:25.0
New from Unitek Eapro is a series of desktop systems for hot bar bonding applications.
Industry News | 2003-06-12 08:24:37.0
An adaptive tool prevents small and/or light components "lifting" or "floating" on printed circuit board assemblies during the wave solder process.
Technical Library | 2023-01-17 17:27:13.0
Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The degree of wetting, the microstructure (in particular the intermetallic layer), and the inherent strength of the solder all factor into the reliability of the solder joint. This paper presents experimental results on the effect of reflow profile on both 63%Sn 37%Pb (SnPb) and 96.5%Sn 3.0%Ag 0.5%Cu (SAC 305) solder joint shear force. Specifically, the effect of the reflow peak temperature and time above solder liquidus temperature are studied. Nine reflow profiles for SAC 305 and nine reflow profiles for SnPb have been developed with three levels of peak temperature (230 o C, 240 o C, and 250 o C for SAC 305; and 195 o C, 205 o C, and 215 o C for SnPb) and three levels of time above solder liquidus temperature (30 sec., 60 sec., and 90 sec.). The shear force data of four different sizes of chip resistors (1206, 0805, 0603, and 0402) are compared across the different profiles. The shear force of the resistors is measured at time 0 (right after assembly). The fracture surfaces have been studied using a scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS)
Technical Library | 2023-09-07 14:38:31.0
A repeat customer specializing in high-technology interconnect, sensor, and antenna solutions, partnered with us to dispense small volumes of solder paste (Indium 10.1 SAC305 T6SG 78%m) onto backplane connectors – gold pads 0.175mm x 0.225mm. We performed a test requiring 0.200mm diameter or smaller dots to demonstrate the dispensing capability required.
StencilQuik demonstration video. This breakthrough method allows you to simplify placement/replacement saving 50% or more of time required to rework BGAs or CSPs.This is a well developed BGA rework method. More on the StencilQuik(TM) process here:
MPM UP2000 HiE Screen Printer Substrate treatment Minimum/maximum size 2"x 2"(50.0 mm x50.0 mm) to 20" x 16" (508 mm x 406 mm)(16 "or larger substrate requires special clamps
Training Courses | ON DEMAND | | IPC-A-610 Specialist (CIS)
The Certified IPC-A-610 Specialist (CIS) training focuses on the acceptance requirements for the manufacture of electrical and electronic assemblies
Training Courses | ON DEMAND | | IPC-A-610 Specialist (CIS)
The Certified IPC-A-610 Specialist (CIS) training focuses on the acceptance requirements for the manufacture of electrical and electronic assemblies
Career Center | Tempe, La Massana | Production
Insert components into a printed circuit board in preparation for soldering. Inspect own work and team members for defects. Properly document problems that occur. Kit parts using bar code reader. May set up and operate automatic machines that are com
Career Center | Mesa, Arizona USA | Production
Great opportunity with growing Tempe Company! Temp to hire Class II and III assemblers needed. First shift hours: Monday-Friday 6:45am to 3:15pm (half hour lunch) Second shift hours: Monday-Friday 3:30pm to 12:00am (half hour lunch) Class II s
America, especially Sn3.0Ag0.5Cu (SAC305), the
SMTnet Express, April 13, 2017, Subscribers: 30,391, Companies: 10,572, Users: 23,128 A Study to Determine the Impact of Solder Powder Mesh Size and Stencil Technology Advancement on Deposition Volume when Printing Solder Paste Karl Seelig, Tim O
Surface Mount Technology Association (SMTA) | https://www.smta.org/knowledge/proceedings_abstract.cfm?PROC_ID=5255
Dissolution Rate of Specific Elements in SAC305 Solder 中文 MEMBERS LOGIN Membership Become a Member! Renew Membership About SMTA Ambassadors Benefits Classifications Member Directory Member Directory Corporate Suppliers Corporate Users Consultants List Advertisers Update Your Info
| https://www.smtfactory.com/Solder-Bar-pl3991858.html
Solder Bar from China, Solder Bar Manufacturer & Supplier - I.C.T SMT Machine English Bahasa indonesia Сербия Česky Dansk Deutsch Español
