Industry Directory | Consultant / Service Provider / Equipment Dealer / Broker / Auctions / Manufacturer / Manufacturer's Representative
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( Loader/Unloader,SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service
Industry Directory | Manufacturer
Cut Tape Feeder Products for Printed Circuit Board Assembly (Attaches easily to your existing feeder) (Feeds short segments 3" or the full reel)
Eliminate Body Stress with Versatile CF-8 GPD's CF-8 eliminates component body stress. Versatility is the key word for the CF-8. Simple tooling changes make short or long run production jobs quick and easy. Capabilities Meets exacting military s
KS-635 Lead-free Fully Computer-controlled Reflow Oven Model KS-635 Heating part parameter Number of heating zones Up 6 down 6 Length of heating zone 2100mm Heating method Hot Air
Used SMT Equipment | Pick and Place/Feeders
This lot contains three items: (1) 80 F5 Dimensions: 78" x 64" x 72" (1) WPW 80F/F4 930mm Dimensions: 60" x 36" x 60" (1) Line Controller Setup Serial: 662-12000151
Used SMT Equipment | Pick and Place/Feeders
This lot contains three items: (1) 80 F5 HM Dimensions: 78" x 64" x 72" (1) WPW/3-950 Dimensions: 60" x 36" x 60" (1) Line Controller Setup Dimensions: 48" x 32" x 58"
Industry News | 2003-06-10 08:16:44.0
The following text describes the application of NWA Quality Analyst to quality control in the assembly of electronic components.
Industry News | 2020-01-23 17:30:46.0
ASYMTEK brings its latest fluid dispensing and conformal coating solutions to IPC APEX EXPO, San Diego, CA, in booth 1611. New at IPC APEX is the ASYMTEK Vortik™ family of progressive cavity pumps (PCP), with the smallest depositions possible on the market today. The VPs, VPm, and VPg pumps rely on positive displacement to provide continuous needle dispensing of one- and two-component fluids with high-volumetric accuracy, increased reliability, and reduced cycle time. At 0.2 microliters per second, the Vortik VPs offers the lowest flowrate and smallest depositions possible across all PCP pumps available in the market today - delivering precise control of narrow lines and small shots for two-component mixed fluids.
Technical Library | 2015-04-16 16:11:43.0
Solder ball height inspection is essential to the detection of potential connectivity issues in semi-conductor units. Current ball height inspection tools such as laser profiling, fringe projection and confocal microscopy are expensive, require complicated setup and are slow, which makes them difficult to use in a real-time manufacturing setting. Therefore, a reliable, in-line ball height measurement method is needed for inspecting units undergoing assembly. (...) In this paper, an automatic, stereo vision based, in-line ball height inspection method is presented. The proposed method includes an imaging setup together with a computer vision algorithm for reliable, in-line ball height measurement.
Technical Library | 2016-02-04 19:11:47.0
In a typical mechatronic manufacturing functional test setup, actual load simulations are usually done by connecting the DUT outputs to power or ground in order to establish either a high or low side driver. Each output is connected with different load and the test will either be sequential or concurrent. At lower power levels, these can usually be managed with general purpose switches. However, when it comes to higher power levels of currents more than 5 amps, such switching and loading might pose a greater challenge. Furthermore, critically in the manufacturing line, the tradeoff between cost and test time would have a great influence on the test strategy.This paper will present some key points to design a cost effective high power switching and load management solution.
Eliminate Body Stress with Versatile CF-8 GPD's CF-8 eliminates component body stress. Versatility is the key word for the CF-8. Simple tooling changes make short or long run production jobs quick and easy. Capabilities Meets exacting military s
KS-2425Z4 desktop SMT pick and place machine is a current market fastest actual mounting speed, the most stable performance and the best quality equipment. With marble mounting platform, 4 Heads +56 Feeder stations in one take and stick, support pneu
Career Center | Southlake, Texas USA | Maintenance
Troubleshoot & Maintain: Siemens (Siplace) placement machines, JOT, MPM Maintain and repair Siplace Placement Feeder Operating SMT equipment during normal production runs Ensuring the highest quality of the paste printing, placement, and reflow p
Career Center | Newbury Park, California USA | Engineering,Maintenance,Production,Quality Control
MUST BE: Proficient with Stencil Print Operations. Familiarity with SMT component types and packages. Ability to read and understand procedure document and work instructions. Operate fully automated SMT, Surface Mount Lines including: Screen Pr
Career Center | Guadalajara, Jalisco Mexico | Engineering,Management,Sales/Marketing
Summary of achievements Company in GDL, Siemens recognized as a partner I had been acting as the interface between the customer and Siemens EAS. This site had 107 SIPLACE machines in three different buildings in the same campus, and I was coor
Career Center | Austin, Texas USA | Engineering,Maintenance,Production,Research and Development,Technical Support
SMT equipment, process, and programming support for Fuji, Siemens, Universal, MPM, and Dek machines using Tecnomatix Exaline, UniCam, FujiCam, F4G, MCS, and Siplace software. Programming includes PD library development, administration, and naming con
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/asymtek/your-process/applications-corner/4-expert-setup-tips-1k-tim-application
4 Expert Setup Tips - 1K TIM Application ASYMTEK Products Corporate | Global Directory | Languages Division Only All of Nordson Fluid Dispensing Systems Jets
GPD Global | https://www.gpd-global.com/pdf/doc/Advanced-FPC-Real-Time-Controller-User-Guide-22940009.pdf
. CAUTION: All hardware setup must be complete prior to setting the controller Online (i.e., air output in line with the fluid pressure sensor). A B 9/25/20 GPD Global® 17 Advanced FPC Real Time Controller Operating instructions Select units of measure If you
