Industry Directory | Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
New PEM® SMTSSS™ ReelFast® SNAP-TOP® standoff fasteners from PennEngineering® hold printed circuit boards securely in assemblies without requiring mating screws or other loose threaded hardware to complete attachment. These unthreaded standoffs prom
SemiPack's capabilities range from fully automatic to manual processing; extensive cropping and forming capabilities; active and passive component processing; axial to radial lead forming servicing; and snap-in and stand-off forms. For SMT processi
Electronics Forum | Thu Nov 13 22:20:48 EST 2008 | davef
For your pad layout and spacing between components, look here: http://portal.ipc.org/Purchase/ProductDetail.aspx?Product_code=77b562c1-b8f8-db11-8a6a-005056875b22 For your standoff height in SMT, we do not concern ourselves with standoff height. It
Electronics Forum | Wed Nov 12 04:34:17 EST 2008 | kywl
Hi all, Assuming that i were to design a PCB and there are multiple components, what is the minimum spacing required to ensure that i won't have problems in my SMT process later on? Also, is there a minimum component stand-off height spec as well?
Industry News | 2010-11-24 13:31:13.0
Count On Tools Inc., a leading provider of precision components and SMT spare parts, announces that it now offers Glue Dispense Nozzles for the Universal Instruments GDM line of equipment.
Parts & Supplies | Chipshooters / Chip Mounters
Below universal auto insertion parts are Manufactured in China,so no need to describe too much about price,what's the difference is that you will surely like it when you try them on machines,just based on the proved quality,please contact louis@smt-m
Technical Library | 2017-08-17 12:28:30.0
At SMT assembly, flux outgassing/drying is difficult for devices with poor venting channel, and resulted in insufficiently dried/burnt-off flux residue for no-clean process. Examples including: Large low stand-off components such as QFN, LGA Components covered under electromagnetic shield which has either no or few venting holes Components assembled within cavity of board Any other devices with small open space around solder joints
Technical Library | 2020-11-24 23:01:04.0
The miniaturization trend is driving industry to adopting low standoff components or components in cavity. The cost reduction pressure is pushing telecommunication industry to combine assembly of components and electromagnetic shield in one single reflow process. As a result, the flux outgassing/drying is getting very difficult for devices due to poor venting channel. This resulted in insufficiently dried/burnt-off flux residue. For a properly formulated flux, the remaining flux activity posed no issue in a dried flux residue for no-clean process. However, when venting channel is blocked, not only solvents remain, but also activators could not be burnt off. The presence of solvents allows mobility of active ingredients and the associated corrosion, thus poses a major threat to the reliability. In this work, a new halogen-free no-clean SnAgCu solder paste, 33-76-1, has been developed. This solder paste exhibited SIR value above the IPC spec 100 MΩ without any dendrite formation, even with a wet flux residue on the comb pattern. The wet flux residue was caused by covering the comb pattern with 10 mm × 10 mm glass slide during reflow and SIR testing in order to mimic the poorly vented low standoff components. The paste 33-76-1 also showed very good SMT assembly performance, including voiding of QFN and HIP resistance. The wetting ability of paste 33-76-1 was very good under nitrogen. For air reflow, 33-76-1 still matched paste C which is widely accepted by industry for air reflow process. The above good performance on both non-corrosivity with wet flux residue and robust SMT process can only be accomplished through a breakthrough in flux technology.
we have many universal gold plus feeders to sell . www.smt-store.com
we have many hitachi equipment and hitachi feeders to sell . if you want to know more , please contact us tina@smtfeeders.cn
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
3 Road Xintang, Fuhai Street,Fuyong
Shenzhen, 30 China
Phone: 13713862102