New Equipment | Solder Materials
Tip tinner to aid in cleaning and re-tinning solder iron tips de-wetted by use which can’t be repaired with sponge pads and cored solder wire. Use of TTC100C LEAD FREE Tip Tinner offers the following advantages: Lead Free SN100C tin/copper/nic
In-Line X-ray Inspection System Automatically in-line inspect Solder joint defects of PCBA and other defects on Hidden Components. Able to judge Good/NG fast with inspection speed of 1sec/FOV and the program can set ROIs conveniently. Performing X-r
Industry News | 2018-10-18 08:21:10.0
How to Prevent Non-Wetting Defect during the SMT Reflow Process
Industry News | 2021-08-13 12:58:35.0
The SMTA Capital Chapter, Carolinas Chapter and Philadelphia Chapter are excited to host their first ever tri-chapter event, Mid-Atlantic Advanced Learning Session - Failure is Never an Option, A Deep Dive into Failure Analysis.
Technical Library | 1999-05-09 13:05:12.0
This Technical Note discusses the construction of solder tips, the various failure modes associated with tip plating (cracking, wear, corrosion, and dewetting), how to diagnose those failure modes, and specific practices that can be taken to minimize or eliminate each one.
Technical Library | 2013-02-07 17:01:46.0
Silicone contamination is known to have a negative impact on assembly processes such as soldering, adhesive bonding, coating, and wire bonding. In particular, silicone is known to cause de-wetting of materials from surfaces and can result in adhesive failures. There are many sources for silicone contamination with common sources being mold releases or lubricants on manufacturing tools, offgassing during cure of silicone paste adhesives, and residue from pressure sensitive tape. This effort addresses silicone contamination by quantifying adhesive effects under known silicone contaminations. The first step in this effort identified an FT-IR spectroscopic detection limit for surface silicone utilizing the area under the 1263 cm-1 (Si-CH3) absorbance peak as a function of concentration (µg/cm2). The next step was to pre-contaminate surfaces with known concentrations of silicone oil and assess the effects on surface wetting and adhesion. This information will be used to establish guidelines for silicone contamination in different manufacturing areas within Harris Corporation... First published in the 2012 IPC APEX EXPO technical conference proceedings.
![[SEC] 3D In-line AXI Solution X-eye 6300 X-ray Inspection Machine](https://img.youtube.com/vi/w-_v-XDRKro/sddefault.jpg)
3D In-line Automated X-ray Inspection system (machine) Model: X-eye 6300 X-ray Tube: 160kV / 500 µa Table Size: Max. 330 x 250mm Min. 50 x 50mm Detector: 12 inch FPXD Defection type (Application): BGA, PoP, chip, QFN, QFP, etc. - High-speed In-lin
Training Courses | | | IPC-A-610 Trainer (CIT)
The Certified IPC-A-610 Trainer (CIT) courses recognize individuals as qualified trainers in the area of quality assurance of electrical and electronic assemblies and prepares them to deliver Certified IPC-A-610 (CIS) training.
Training Courses | | | PCB Assembly Courses
The PCB assembly courses provide knowledge of different processes and equipment used in TH and SMT assembly of printed circuit boards.
Career Center | , Gjirokaster Philippines | Engineering,Production,Quality Control,Research and Development,Technical Support
TEST Engineer FOXCONN(Hon Hai Precision Ind., Ltd., Co)-formerly AMBIT Microsystems Co. Inc. Research and Development Center 5F-1 No. 5, Hsin Ann Road, Science-Based Industrial Park, Hsinchu City, Taiwan, R.O.C. General Job Functions: PCBA Testing u
A Review of Test Methods and Classifications for Halogen-Free Soldering Materials A Review of Test Methods and Classifications for Halogen-Free Soldering Materials Over the last few years, there has been an increase in the evaluation and use
| http://etasmt.com/cc?ID=te_news_bulletin,23572&url=_print
. Check against manufacturer’s specifications. PCB Dewetting PCB Dewetting is a condition that results when molten solder has coated a surface and then receded, leaving irregularly shaped mounds of solder separated by areas covered with a thin
| https://www.eptac.com/soldertips/solder-paste-shelf-life-and-testing/
. The adverse affect would be un-reflowed solder paste, insufficient reflow, solder balls, dewetting, etc. The recommendations would be to perform a solderability test, slump test and flux activity test on the solder paste itself and see if it still performs to the original standards of the material
.gif)
