New Equipment | Education/Training
This course is designed for students that require the hands-on skill and knowledge to reliably remove and install many types of the most complex BGA components. Students are taught methods for safe and reliable BGA component rework using a top of the
New Equipment | Rework & Repair Services
BGA Reballing Services BEST provides BGA reballing services for your plastic-, ceramic- and metalbodied components down to 0.3mm pitch. We have the ability to develop the BGA reballing process you want with a variety of deballing methods and machine
Electronics Forum | Tue Jul 01 11:15:43 EDT 2003 | PH
Are these caps on the bottom side or topside? Bottomside could be the glue dots are too big for the caps your putting down, the glue cures and then the solder is putting force on the edges of the cap causing cracks.. Other than that agree with oth
Electronics Forum | Mon Jul 07 00:11:10 EDT 2003 | praveen
if the capacitors are placed very near to the edge and their position is 90 deg than it may cause crack.4thly if the reflow ramp rate is more than 3 deg C then it may crack. 5th ly if the solderin tip temp. is very high and soldering bit is very thi
Industry News | 2018-04-18 18:06:14.0
SMTA Europe announces Session 6 Technical Program on Automotive Electronics at the “Electronics in Harsh Environments Conference” to be held in Amsterdam, Netherlands, on April 25th, 2018.
Industry News | 2022-01-10 16:55:15.0
The SMTA Capital Chapter Officer team is excited to provide our members with a free technical webinar on "Use of Photonic Soldering to Rework Chip Components" presented by Dr. Vahid Akhavan, Global Application Engineer at NovaCentrix. The presentation will take place on January 20th at 12:00am EST.
.jpg)
Parts & Supplies | Assembly Accessories
12MM Calibration Tape .12MM Calibration Tape 20 Inch Folding Bike Ravel Case 20 Inch Folding Bike ravel Case 4*4.1200pcs/bag M0604 8MM Calibration Tape .8MM Calibration Tape 90 degree drive set 90 degree drive set A2E BGA Rework Station Temp Con
Parts & Supplies | Circuit Board Assembly Products
1). 80*50mm/1up, Bergquist Thermal Clad aluminium backed 2). LTI-04503,MP-06503,ML-11006 3). Ceramic dielectric material, conductivity: 1.3W/m-k, 2.2W/m-k, 4). 1.6mm thick, single sided, 35μm (1 oz) 5). Black solder mask/no ident 6). CNC rout outli
Technical Library | 1999-07-21 09:04:04.0
A high volume manufacturer of printed circuit boards (PCBs) had attempted for many years to locate an adhesive that was robust enough to meet their manufacturing needs. This proved to be a challenge because they needed the adhesive to accommodate a wide range of different dispensing equipment and board designs. The two key performance criteria required from the adhesive were dispensability and adhesion...
Technical Library | 2023-08-04 15:27:30.0
A designed experiment evaluated the influence of several variables on appearance and strength of Pb-free solder joints. Components, with leads finished with nickel-palladium-gold (NiPdAu), were used from Texas Instruments (TI) and two other integrated circuit suppliers. Pb-free solder paste used was tin-silver-copper (SnAgCu) alloy. Variables were printed wiring board (PWB) pad size/stencil aperture (the pad finish was consistent; electrolysis Ni/immersion Au), reflow atmosphere, reflow temperature, Pd thickness in the NiPdAu finish, and thermal aging. Height of solder wetting to component lead sides was measured for both ceramic plate and PWB soldering. A third response was solder joint strength; a "lead pull" test determined the maximum force needed to pull the component lead from the PWB. This paper presents a statistical analysis of the designed experiment. Reflow atmosphere and pad size/stencil aperture have the greatest contribution to the height of lead side wetting. Reflow temperature, palladium thickness, and preconditioning had very little impact on side-wetting height. For lead pull, variance in the data was relatively small and the factors tested had little impact.
Dennis Odonnell , Vice President of Precision PCB Services, Inc., Oroville CA Explains How to Evaluate a BGA Rework Station ! #BGA Rework Stations http://www.pcb-repair.com/bga-rework-station/
Dennis Odonnell , Vice President of Precision PCB Services, Inc., Oroville CA Explains How to Evaluate a BGA Rework Station ! #BGA Rework Stations http://www.pcb-repair.com/bga-rework-station/
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Events Calendar | Mon Apr 12 00:00:00 EDT 2021 - Mon Apr 12 00:00:00 EDT 2021 | ,
Europe Chapter Webinar: Tombstoning Components during Reflow Soldering - Causes & Cures
Career Center | Melbourne, Florida USA | Engineering
Advanced Manufacturing Technology Position Description Job Description: AMT Engineer � Level 4 Support IR&D and Program activities Division wide working on the development, qualification, and implementation of electronic packaging technologies, wi
Career Center | Space Coast, Florida USA | Engineering,Research and Development
Board Level Assembly BGA Expert! We are in need of an Electronic Packaging or Advanced Manufacturing Engineer to work with the Advanced Manufacturing Technology Group of a major Florida based Communications company. Support IR&D and Program activit
SMT Express, Volume 5, Issue No. 8 - from SMTnet.com Equipment Impacts of Lead Free Wave Soldering The popular tin (Sn) rich lead free solders are causing severe corrosion to many of the materials used in today�s Wave Solder systems
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/solder-mask-on-0-40-pitch-qfn_topic3127.html
Solder Mask On 0.40 Pitch QFN - PCB Libraries Forum Forum Home > Libraries > Footprints / Land Patterns New Posts FAQ Search Events Register Login Solder Mask On
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/asymtek/fluid-types/solder-mask?con=t&page=6
Solder Mask | Nordson ASYMTEK ASYMTEK Products Corporate | Global Directory | Languages Division Only All of Nordson Fluid Dispensing Systems Jets
COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.
2481 Hilton Drive
Gainesville, GA USA
Phone: (770) 538-0411
