New Equipment | Solder Materials
Indium Corporation manufactures high quality solder powders and pastes. Powders are available in hundreds of alloys and a full range of sizes. Solder pastes can be made from these powders using a wide variety of flux vehicles to get the best fit for
Electronics Forum | Fri Oct 05 18:59:53 EDT 2001 | Dan Steffler
I have had an issue where solder has contaminated gold plated pads (fingers) where it is not acceptable. The pads must remain perfectly coplaniar for a LCD zebra strip to lay accross them. Does anyone know of a way to remove the marriage level of s
Electronics Forum | Sat Jul 29 13:36:57 EDT 2006 | Chunks
Davef is right about the amount, but why are using gold to solder too when other finishes are avaiable?
Industry News | 2012-01-07 21:33:05.0
To support the consistent and rapid growth in Eastern Europe’s electronics assembly industry, IPC will hold its second annual IPC Conference on Electronics Assembly: Soldering, Assembly & Inspection in Budapest, Hungary, on 20-22 March 2012. This three-day event includes workshops, a two-day technical conference and a tabletop exhibition, providing myriad opportunities for participants to network with industry experts and gain insight into new technologies and trends in this key market.
Industry News | 2018-12-08 03:29:29.0
SMT Dictionary – Surface Mount Technology Acronym and Abbreviation
Technical Library | 2023-08-04 15:27:30.0
A designed experiment evaluated the influence of several variables on appearance and strength of Pb-free solder joints. Components, with leads finished with nickel-palladium-gold (NiPdAu), were used from Texas Instruments (TI) and two other integrated circuit suppliers. Pb-free solder paste used was tin-silver-copper (SnAgCu) alloy. Variables were printed wiring board (PWB) pad size/stencil aperture (the pad finish was consistent; electrolysis Ni/immersion Au), reflow atmosphere, reflow temperature, Pd thickness in the NiPdAu finish, and thermal aging. Height of solder wetting to component lead sides was measured for both ceramic plate and PWB soldering. A third response was solder joint strength; a "lead pull" test determined the maximum force needed to pull the component lead from the PWB. This paper presents a statistical analysis of the designed experiment. Reflow atmosphere and pad size/stencil aperture have the greatest contribution to the height of lead side wetting. Reflow temperature, palladium thickness, and preconditioning had very little impact on side-wetting height. For lead pull, variance in the data was relatively small and the factors tested had little impact.
Technical Library | 2013-01-17 15:37:21.0
A problem exists with electroless nickel / immersion gold (ENIG) surface finish on some pads, on some boards, that causes the solder joint to separate from the nickel surface, causing an open. The solder has wet and dissolved the gold. A weak tin to nickel intermetallic bond initially occurs, but the intermetallic bond cracks and separates when put under stress. Since the electroless nickel / immersion gold finish performs satisfactory in most applications, there had to be some area within the current chemistry process window that was satisfactory. The problem has been described as a 'BGA Black Pad Problem' or by HP as an 'Interfacial Fracture of BGA Packages…'[1]. A 24 variable experiment using three different chemistries was conducted during the ITRI (Interconnect Technology Research Institute) ENIG Project, Round 1, to investigate what process parameters of the chemical matrix were potentially satisfactory to use and which process parameters of the chemical matrix need to be avoided. The ITRI ENIG Project has completed Round 1 of testing and is now in the process of Round 2 TV (Test Vehicle) build.
SMTnet Express, July 1, 2015, Subscribers: 22,969, Members: Companies: 14,445, Users: 38,464 Reliability Screening of Lower Melting Point Pb-Free Alloys Containing Bi Joseph M. Juarez, Michael Robinson, Joel Heebink; Honeywell International
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/07/Vacuum-Void-Reduction-Reflow.pdf
of the void relative to the soldered interfaces where fatigue cracks are expected to propagate (see Figure 2). Because the voiding is not always centered in the solder sphere or on the pads (see x-ray images), cross sectional images may not represent
PCB Libraries, Inc. | https://www.pcblibraries.com/Forum/smd-solder-mask-defined-and-nsmd-pads_topic1768.html
+/- 0.05 mm. You do not want any solder mask on the pad so the minimum solder mask opening should be 0.05 mm. The exception to this rule is Flexible Circuit libraries normally have a
COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.
2481 Hilton Drive
Gainesville, GA USA
Phone: (770) 538-0411
